How To Install a Tank Base Sealant with Belzona 3111
14.1 هزار بار بازدید -
5 سال پیش
-
In this video we are
In this video we are demonstrating an installation of a tank base sealant using #Belzona 3111.
Belzona #tankbase sealing system helps replace failed #tankchime seals, stops water penetration and protects tank bottoms against crevice #corrosion.
By installing a sealing system, you can prolong the tank base service life and reduce the risk of a tank demolition and replacement which often associates with high costs.
The system offers an easy, safe and rapid installation. It does not require specialist tools or hot work permits.
In the next couple of minutes, you will learn how to successfully conduct this application.
Step-by-step application guidelines:
1. Light corrosion on the annular ring and tank wall can be manually prepared using handheld tools. The concrete base should also be abraded to remove all loose and deteriorated material.
2. Define the repair area using tape.
3. Prime the repair area using Belzona 3921 Conditioner. Mix base and solidifier thoroughly and apply the mixed material to the prepared tank wall, annular ring and the concrete base using a brush.
4. Allow the conditioner to dry for a minimum of four hours, insert a backer rod into the void between the tank chime and the concrete base.
5. Apply bridging tape across the tank base joint.
6. Define the repair area with a tape to prepare for the coating application.
7. Pre-measured and pre-cut pieces of reinforcement sheet can be applied with the first coat of the coating or embedded into it while it is still wet.
Pre-cut pieces of reinforcement sheet should not be stretched or creased and should be positioned to follow the contour of the surface.
8. Once the first coat is dry, apply the second coat of Belzona 3111.
9. All pinholes and areas not wetted out previously should be fully covered and filled by the second layer to produce a continuous unbroken film.
10. Remove the tape and allow the coating to dry.
Products used for this application:
Belzona 3111
https://www.belzona.com/en/products/3...
Belzona 3921 (GSC Surface Conditioner)
0:46 Surface preparation
1:24 Condition repair area
2:23 Insert backer rod
3:25 Apply Belzona 3111
4:10 Apply second coat
For more information about this application, contact your local Belzona representative:
https://www.belzona.com/en/contact.aspx
Belzona #tankbase sealing system helps replace failed #tankchime seals, stops water penetration and protects tank bottoms against crevice #corrosion.
By installing a sealing system, you can prolong the tank base service life and reduce the risk of a tank demolition and replacement which often associates with high costs.
The system offers an easy, safe and rapid installation. It does not require specialist tools or hot work permits.
In the next couple of minutes, you will learn how to successfully conduct this application.
Step-by-step application guidelines:
1. Light corrosion on the annular ring and tank wall can be manually prepared using handheld tools. The concrete base should also be abraded to remove all loose and deteriorated material.
2. Define the repair area using tape.
3. Prime the repair area using Belzona 3921 Conditioner. Mix base and solidifier thoroughly and apply the mixed material to the prepared tank wall, annular ring and the concrete base using a brush.
4. Allow the conditioner to dry for a minimum of four hours, insert a backer rod into the void between the tank chime and the concrete base.
5. Apply bridging tape across the tank base joint.
6. Define the repair area with a tape to prepare for the coating application.
7. Pre-measured and pre-cut pieces of reinforcement sheet can be applied with the first coat of the coating or embedded into it while it is still wet.
Pre-cut pieces of reinforcement sheet should not be stretched or creased and should be positioned to follow the contour of the surface.
8. Once the first coat is dry, apply the second coat of Belzona 3111.
9. All pinholes and areas not wetted out previously should be fully covered and filled by the second layer to produce a continuous unbroken film.
10. Remove the tape and allow the coating to dry.
Products used for this application:
Belzona 3111
https://www.belzona.com/en/products/3...
Belzona 3921 (GSC Surface Conditioner)
0:46 Surface preparation
1:24 Condition repair area
2:23 Insert backer rod
3:25 Apply Belzona 3111
4:10 Apply second coat
For more information about this application, contact your local Belzona representative:
https://www.belzona.com/en/contact.aspx
5 سال پیش
در تاریخ 1397/11/16 منتشر شده
است.
14,167
بـار بازدید شده