How to Add BMW FEM/BDC Key By CGDI BMW
6.9 هزار بار بازدید -
3 سال پیش
-
CGDI BMW Add FEM/BDC Key
CGDI BMW Add FEM/BDC Key Tutorials:
Equipment: CGDI BMW(https://bit.ly/3vhkmrq), FEM/BDC platform(https://bit.ly/3u56j8a)
Function: FEM/BDC key match ,BMW F/G series program(coding)
Preparation before operation:
1. Need to do it on bench . pull out the FEM/BDC board
2. Need working key or DME ISN
3. Need blank key that can support FEM/BDC car
Brife description :
1.Check the things that you need to use
2.If the FEM version not support ,need to downgrade it to support version
3.We use 8 pin adapter or programmer to do preprocess the FEM/BDC steps
4.After preprocess finished ,we can add key or do mileage reset or other functions
5.After add key succeed , we better program the FEM/BDC back to original status .
Detail Steps:
1 Read key information
1.1 Read original car key information
1.2 Check new key is blank
2 Check FEM/BDC version
If it tip that FEM/BDC Version is not supported ,please upgrade FEM/BDC first
Go to BMW F/G series program page to downgrade the version .
It has another manual how to do it .
3 Preprocessing steps
3.1 chip pin 1 place
Note: The 8 pin adapter red cable is pin 1 . (you can follow the pic to operate )
3.2 FEM/BDC key match page to do preprocess
4 Add key (with key or with out key )
4.1 Add key with working key
4.2 Add key without key (need DME ISN)
5 Program to your FEM/BDC back to original status
Note: If key not work well, Enter into BMW F/G series program function, choose BDC_BODY and click “start programming”, after programming success, need to enter F series coding to code the FEM/BDC. It will solve your key problem .And your FEM/BDC will back to origianl status .
5.1 Program your FEM/BDC
5.2 Code your FEM/BDC
5.3 Then back to FEM/BDC key match page
It will show you not support version now .It has back to your original version ,original status .
Equipment: CGDI BMW(https://bit.ly/3vhkmrq), FEM/BDC platform(https://bit.ly/3u56j8a)
Function: FEM/BDC key match ,BMW F/G series program(coding)
Preparation before operation:
1. Need to do it on bench . pull out the FEM/BDC board
2. Need working key or DME ISN
3. Need blank key that can support FEM/BDC car
Brife description :
1.Check the things that you need to use
2.If the FEM version not support ,need to downgrade it to support version
3.We use 8 pin adapter or programmer to do preprocess the FEM/BDC steps
4.After preprocess finished ,we can add key or do mileage reset or other functions
5.After add key succeed , we better program the FEM/BDC back to original status .
Detail Steps:
1 Read key information
1.1 Read original car key information
1.2 Check new key is blank
2 Check FEM/BDC version
If it tip that FEM/BDC Version is not supported ,please upgrade FEM/BDC first
Go to BMW F/G series program page to downgrade the version .
It has another manual how to do it .
3 Preprocessing steps
3.1 chip pin 1 place
Note: The 8 pin adapter red cable is pin 1 . (you can follow the pic to operate )
3.2 FEM/BDC key match page to do preprocess
4 Add key (with key or with out key )
4.1 Add key with working key
4.2 Add key without key (need DME ISN)
5 Program to your FEM/BDC back to original status
Note: If key not work well, Enter into BMW F/G series program function, choose BDC_BODY and click “start programming”, after programming success, need to enter F series coding to code the FEM/BDC. It will solve your key problem .And your FEM/BDC will back to origianl status .
5.1 Program your FEM/BDC
5.2 Code your FEM/BDC
5.3 Then back to FEM/BDC key match page
It will show you not support version now .It has back to your original version ,original status .
3 سال پیش
در تاریخ 1400/02/09 منتشر شده
است.
6,981
بـار بازدید شده