How to Install Ultra-Thin Exterior Lighting | All About Lights | Ask This Old House
377.5 هزار بار بازدید -
8 سال پیش
-
Scott installs ultra-thin, LED lights
Scott installs ultra-thin, LED lights on a garage to replace a broken flood light.
#ThisOldHouse #AskTOH
SUBSCRIBE to This Old House: http://bit.ly/SubscribeThisOldHouse
Time: 2-3 hours
Cost: $120-150
Tools:
Pliers
Hole Saw
Screwdriver
Wire nuts
Shopping List:
LED lights
14-2, NM electrical wire
Astronomic Timer Switch
Steps:
1. Before doing any electrical work, ensure power is turned off at the breaker. Confirm the power is off using an electric tester.
2. Remove the current light fixture and disconnect the wires.
3. Measure and mark where each new light fixture will go, maintaining even spacing.
4. Use a hole saw to drill openings for the new lights.
5. Fish 14-2 electrical wire from the main power source to one fixture. Fish wire to any additional fixtures
6. Make the electrical connections to each junction box and tie the wires together using wire nuts.
7. Clip each LED light into its hole.
8. Replace the existing light switch with an astronomic timer switch that will automatically turn the lights on at dusk.
9. Restore power at the breaker and test the lights and switch.
About This Old House TV:
This Old House is the No. 1 multimedia home enthusiast brand, offering trusted information and expert advice through award-winning television, a highly regarded magazine, and an information-driven website. This Old House and Ask This Old House are produced by This Old House Ventures, LLC and are presented on PBS by WGBH Boston.
Follow This Old House and Ask This Old House:
Facebook: http://bit.ly/ThisOldHouseFB
Twitter: http://bit.ly/ThisOldHouseTwitter
http://bit.ly/AskTOHTwitter
Pinterest: http://bit.ly/ThisOldHousePinterest
Instagram: http://bit.ly/ThisOldHouseIG
Tumblr: http://bit.ly/ThisOldHouseTumblr
How to Install Ultra-Thin Exterior Lighting | All About Lights | Ask This Old House
thisoldhouse
#ThisOldHouse #AskTOH
SUBSCRIBE to This Old House: http://bit.ly/SubscribeThisOldHouse
Time: 2-3 hours
Cost: $120-150
Tools:
Pliers
Hole Saw
Screwdriver
Wire nuts
Shopping List:
LED lights
14-2, NM electrical wire
Astronomic Timer Switch
Steps:
1. Before doing any electrical work, ensure power is turned off at the breaker. Confirm the power is off using an electric tester.
2. Remove the current light fixture and disconnect the wires.
3. Measure and mark where each new light fixture will go, maintaining even spacing.
4. Use a hole saw to drill openings for the new lights.
5. Fish 14-2 electrical wire from the main power source to one fixture. Fish wire to any additional fixtures
6. Make the electrical connections to each junction box and tie the wires together using wire nuts.
7. Clip each LED light into its hole.
8. Replace the existing light switch with an astronomic timer switch that will automatically turn the lights on at dusk.
9. Restore power at the breaker and test the lights and switch.
About This Old House TV:
This Old House is the No. 1 multimedia home enthusiast brand, offering trusted information and expert advice through award-winning television, a highly regarded magazine, and an information-driven website. This Old House and Ask This Old House are produced by This Old House Ventures, LLC and are presented on PBS by WGBH Boston.
Follow This Old House and Ask This Old House:
Facebook: http://bit.ly/ThisOldHouseFB
Twitter: http://bit.ly/ThisOldHouseTwitter
http://bit.ly/AskTOHTwitter
Pinterest: http://bit.ly/ThisOldHousePinterest
Instagram: http://bit.ly/ThisOldHouseIG
Tumblr: http://bit.ly/ThisOldHouseTumblr
How to Install Ultra-Thin Exterior Lighting | All About Lights | Ask This Old House
thisoldhouse
8 سال پیش
در تاریخ 1395/11/10 منتشر شده
است.
377,535
بـار بازدید شده