The New $1 Fix for Broken 552 & 1090 Bowflex SelectTech Weight Plate Tabs
9.6 هزار بار بازدید -
3 سال پیش
-
In September 2020 I published
In September 2020 I published a $1 Fix video for SelectTech weight plate tabs. This is an update with what I believe to be a better solution for about the same cost.
If you've broken one or more tabs on your Bowflex SelectTech weight plates, don't waste money by buying used plates that will eventually fail as well. With a little elbow grease and some common tools you can permanently fix your plates and make them Better Than OEM (tm).
Please note that there are countless styles of weld nuts with various tabs, flanges, projections, etc. I showed a very specific 5/16" weld nut obtained at a True Value franchise store (it's a hardware store chain in the U.S.). That happened to be a perfect fit for a 3/8" drill bit. If you purchase a different style or size of weld nut your installation may vary as far as drill bit sizes, and cutouts in the plastic that covers the plates. Any questions, shoot me an email at the address shown below.
If you own the older version of weight plates with the plastic covered tab your center mark to drill the hole can be calculated as follows: 18 - 0.5 (bolt head width in mm).
Cheers,
Average Joe
𝗙𝗢𝗥 𝗔𝗩𝗘𝗥𝗔𝗚𝗘 𝗝𝗢𝗘 𝗣𝗥𝗢𝗗𝗨𝗖𝗧 𝗜𝗡𝗙𝗢 𝗔𝗡𝗗 𝗣𝗥𝗜𝗖𝗜𝗡𝗚, 𝗩𝗜𝗦𝗜𝗧:
www.averagejoeinnovations.com
𝗙𝗢𝗟𝗟𝗢𝗪 𝗢𝗡 𝗜𝗡𝗦𝗧𝗔𝗚𝗥𝗔𝗠:
Instagram: average_joe_innovations_llc
𝗙𝗢𝗟𝗟𝗢𝗪 𝗢𝗡 𝗙𝗔𝗖𝗘𝗕𝗢𝗢𝗞:
Facebook: AverageJoeInnovationsLLC
[𝗗𝗜𝗦𝗖𝗟𝗔𝗜𝗠𝗘𝗥: Bowflex®, SelectTech® trademarks are property of Nautilus®. Nautilus/Bowflex have had zero involvement with the development of AJI product upgrades. They aren't affiliated with AJI in any way, and AJI product upgrades are in no way endorsed by these companies.]
If you've broken one or more tabs on your Bowflex SelectTech weight plates, don't waste money by buying used plates that will eventually fail as well. With a little elbow grease and some common tools you can permanently fix your plates and make them Better Than OEM (tm).
Please note that there are countless styles of weld nuts with various tabs, flanges, projections, etc. I showed a very specific 5/16" weld nut obtained at a True Value franchise store (it's a hardware store chain in the U.S.). That happened to be a perfect fit for a 3/8" drill bit. If you purchase a different style or size of weld nut your installation may vary as far as drill bit sizes, and cutouts in the plastic that covers the plates. Any questions, shoot me an email at the address shown below.
If you own the older version of weight plates with the plastic covered tab your center mark to drill the hole can be calculated as follows: 18 - 0.5 (bolt head width in mm).
Cheers,
Average Joe
𝗙𝗢𝗥 𝗔𝗩𝗘𝗥𝗔𝗚𝗘 𝗝𝗢𝗘 𝗣𝗥𝗢𝗗𝗨𝗖𝗧 𝗜𝗡𝗙𝗢 𝗔𝗡𝗗 𝗣𝗥𝗜𝗖𝗜𝗡𝗚, 𝗩𝗜𝗦𝗜𝗧:
www.averagejoeinnovations.com
𝗙𝗢𝗟𝗟𝗢𝗪 𝗢𝗡 𝗜𝗡𝗦𝗧𝗔𝗚𝗥𝗔𝗠:
Instagram: average_joe_innovations_llc
𝗙𝗢𝗟𝗟𝗢𝗪 𝗢𝗡 𝗙𝗔𝗖𝗘𝗕𝗢𝗢𝗞:
Facebook: AverageJoeInnovationsLLC
[𝗗𝗜𝗦𝗖𝗟𝗔𝗜𝗠𝗘𝗥: Bowflex®, SelectTech® trademarks are property of Nautilus®. Nautilus/Bowflex have had zero involvement with the development of AJI product upgrades. They aren't affiliated with AJI in any way, and AJI product upgrades are in no way endorsed by these companies.]
3 سال پیش
در تاریخ 1400/06/25 منتشر شده
است.
9,664
بـار بازدید شده