How to Test the Polarity of a Speaker and Wiring
193.1 هزار بار بازدید -
3 سال پیش
-
How to test the polarity
How to test the polarity on a speaker and the speaker wiring. I’m slowly finalizing the audio system overhaul on my truck after dealing with a mess of wiring. To ensure all speakers are working correctly, I had to check the polarity on both the speakers and wiring. I was also able to reference a wiring diagram specific for this truck to determine which was positive and negative, this will be based on the color-coding of the wire’s insulation. Finding electrical polarity is used to determine which source is positive and which is negative, this is important on both the wiring and speaker sides. With speakers moving in the correct direction, the amplitude is increased. In simple terms, a higher audio output. If the polarity is mixed between speakers, so they’re not operating in the same direction, one will cancel out the other in opposite movements and you’ll be left with poor audio performance. #caraudio #electronics #music
Website: http://4diyers.com
Patreon: Patreon: 4diyers
Facebook: Facebook: 4diyers
Twitter: Twitter: 4DIYers
Instagram: Instagram: 4diyers
Tumblr: Tumblr: 4diyers
Pintrest: Pinterest: 4diyers
Tools/Supplies Needed:
-multimeter
-AA battery
-jumper cables
Chapters:
00:00 Intro
00:30 What is Polarity
00:40 Speaker Removal
00:57 Speaker Testing
02:07 Fault Symptoms
02:33 Testing the Speaker Wiring
03:58 Repairing the Wiring
Procedure:
There is spade terminals on the rear of the speaker, one is large, the other is smaller. I already know the large terminal is positive and the small terminal is negative. To double-check this, we can use a small amount of voltage. Only use a very small power source, such as a used AA battery which is rated at 1.5 volts. While there is still a risk here, a higher voltage battery can certainly damage the coil in the speaker.
Touch the wires on the battery terminals, one on negative and the other on positive, and watch the speaker movement. Only do this very briefly, while this is a small battery, holding the speaker movement can damage the coil too. Speakers use an electromagnet to push out the speaker. The correct movement of the speaker is to push out, at the moment the speaker is pulling in, so the polarity is wrong. Flipping the battery around, the speaker pushed out so the polarity is correct. Positive is connected to positive and negative is connected to negative.
Cleaning up the mess, I desoldered the wires on the rear, they were removed and the speakers will be connected using spade terminals instead.
There is a very low voltage output to the speakers, using a digital multimeter, set it to the 200 millivolt DC setting.
Ensure the wires do not make contact with each other or the body, otherwise, you’ll create a short. Now is turned on the radio and you’ll need to turn up the sound louder as well. I have music playing, however, to avoid any copyright issues, it’s been muted out.
Connect the positive probe to the one wire and the negative probe to the other, then watch the value. The value will vary based on the audio output, the only thing we’re looking for here is a positive or negative value.
As the value fluctuates, it stays positive, there’s the red probe is on the positive wire and the black probe is on the negative wires. Make notes of the wire casing color, here I’m working with one grey with a blue stripe and the other is a grey with a yellow stripe.
If the probes were reverse, in other words, the polarity is mixed up, you’ll see a negative value like this.
Another process of elimination is using a known ground source and only testing one speaker wire. This known ground can be a known ground wire, body bolt, or in this case, I’m using the steel structural frame under the dashboard. The black probe is used here, then using the red probe, check the wires. The one with the value will be the positive wire, leaving the other wire to be negative.
Unfortunately, the wires are too short to hook up the speakers, I cut them back to expose a clean conductor and soldered on extensions using the leftover wiring from the new amp. I purchased quality spade terminals, there are two sizes. So beyond the wires being color-coded, the spade terminals are also specific to the terminals on the speakers, so they can’t be mixed up. These crimp terminals not only clamp onto the conduction, but they clamp onto the wire’s insulation providing more of a reliable connection and have vinyl covers to protect the terminals.
Thank you to all those who watch my videos and support my content. Don't forget to subscribe to my channel for future tutorial videos and like my video if you found it helpful. New videos are always being uploaded every week!
© 4DIYers 2013
All Rights Reserved
No part of this video or any of its contents may be reproduced, copied, modified or adapted, without the prior written consent of the author.
Website: http://4diyers.com
Patreon: Patreon: 4diyers
Facebook: Facebook: 4diyers
Twitter: Twitter: 4DIYers
Instagram: Instagram: 4diyers
Tumblr: Tumblr: 4diyers
Pintrest: Pinterest: 4diyers
Tools/Supplies Needed:
-multimeter
-AA battery
-jumper cables
Chapters:
00:00 Intro
00:30 What is Polarity
00:40 Speaker Removal
00:57 Speaker Testing
02:07 Fault Symptoms
02:33 Testing the Speaker Wiring
03:58 Repairing the Wiring
Procedure:
There is spade terminals on the rear of the speaker, one is large, the other is smaller. I already know the large terminal is positive and the small terminal is negative. To double-check this, we can use a small amount of voltage. Only use a very small power source, such as a used AA battery which is rated at 1.5 volts. While there is still a risk here, a higher voltage battery can certainly damage the coil in the speaker.
Touch the wires on the battery terminals, one on negative and the other on positive, and watch the speaker movement. Only do this very briefly, while this is a small battery, holding the speaker movement can damage the coil too. Speakers use an electromagnet to push out the speaker. The correct movement of the speaker is to push out, at the moment the speaker is pulling in, so the polarity is wrong. Flipping the battery around, the speaker pushed out so the polarity is correct. Positive is connected to positive and negative is connected to negative.
Cleaning up the mess, I desoldered the wires on the rear, they were removed and the speakers will be connected using spade terminals instead.
There is a very low voltage output to the speakers, using a digital multimeter, set it to the 200 millivolt DC setting.
Ensure the wires do not make contact with each other or the body, otherwise, you’ll create a short. Now is turned on the radio and you’ll need to turn up the sound louder as well. I have music playing, however, to avoid any copyright issues, it’s been muted out.
Connect the positive probe to the one wire and the negative probe to the other, then watch the value. The value will vary based on the audio output, the only thing we’re looking for here is a positive or negative value.
As the value fluctuates, it stays positive, there’s the red probe is on the positive wire and the black probe is on the negative wires. Make notes of the wire casing color, here I’m working with one grey with a blue stripe and the other is a grey with a yellow stripe.
If the probes were reverse, in other words, the polarity is mixed up, you’ll see a negative value like this.
Another process of elimination is using a known ground source and only testing one speaker wire. This known ground can be a known ground wire, body bolt, or in this case, I’m using the steel structural frame under the dashboard. The black probe is used here, then using the red probe, check the wires. The one with the value will be the positive wire, leaving the other wire to be negative.
Unfortunately, the wires are too short to hook up the speakers, I cut them back to expose a clean conductor and soldered on extensions using the leftover wiring from the new amp. I purchased quality spade terminals, there are two sizes. So beyond the wires being color-coded, the spade terminals are also specific to the terminals on the speakers, so they can’t be mixed up. These crimp terminals not only clamp onto the conduction, but they clamp onto the wire’s insulation providing more of a reliable connection and have vinyl covers to protect the terminals.
Thank you to all those who watch my videos and support my content. Don't forget to subscribe to my channel for future tutorial videos and like my video if you found it helpful. New videos are always being uploaded every week!
© 4DIYers 2013
All Rights Reserved
No part of this video or any of its contents may be reproduced, copied, modified or adapted, without the prior written consent of the author.
3 سال پیش
در تاریخ 1400/02/24 منتشر شده
است.
193,149
بـار بازدید شده