Epson L3150 control panel button functions
1.1 هزار بار بازدید -
2 سال پیش
-
Epson L3150 control panel button
Epson L3150 control panel button functions, Checking the Nozzles Using the Product Buttons
You can check the print head nozzles using the buttons on your product.
1. Press the power button to turn the product off.
2. Load a few sheets of plain paper in the product.
3. Hold down the stop button and press the power button to turn the product on.
4. When the product turns on, release both buttons.
The product prints a nozzle check pattern.
Print Head Cleaning
If print quality has declined and the nozzle check pattern indicates clogged nozzles, you can clean the print head. You may not be able to clean the print head when the ink level in any of the tanks is low. You may
have to refill the ink tank first.
You can clean the print head using the buttons on your product.
1. Make sure no product lights are indicating errors.
2. Load a few sheets of plain paper in the product.
3. Hold down the stop button for five seconds to start the cleaning cycle.
The power light flashes throughout the cleaning cycle and stays on when the cleaning cycle is
finished.
Caution: Never turn off the product during a cleaning cycle or you may damage it.
4. Run a nozzle check to confirm that the print head is clean.
5. Do one of the following:
• If there are no gaps, the print head is clean and you can continue printing.
• If there are gaps or the pattern is faint, clean the print head.
If you don’t see any improvement after cleaning the print head up to 3 times, turn off the product and wait
at least 12 hours. Then try cleaning the print head again. If quality still does not improve, run a Power
Cleaning
Press and hold the stop button for 5 seconds until the power light starts to blink and ink charging begins, Enabling Wi-Fi Direct Mode You can enable Wi-Fi Direct mode to allow direct communication between your product and computer or other devices without a wireless router or access point,
1. Hold down the Wi-Fi button and press the network status button until the Wi-Fi light and WiFi Direct light flash alternately. Then release both buttons.
After both lights stop flashing, the Wi-Fi Direct light remains on.
2. Hold down the network status button for about seven seconds to print a network status sheet.
3. Use your computer or wireless device to select the Wi-Fi network name (SSID) and password listed
in the Wi-Fi Direct section of the network status sheet.
You should now be able to print to your product directly from your computer or device. If you cannot
print successfully, repeat the process above and make sure you enter the password exactly as written on the network status sheet.
Using WPS to Connect to a Network
If you have a WPS-enabled router or access point, you can use Wi-Fi Protected Setup (WPS) to connect your device to the network.
1. Press the WPS button on your router or access point.
2. Hold down the Wi-Fi button on your product for about five seconds until the Wi-Fi light and WiFi Direct light flash alternately.
The Wi-Fi light turns green to indicate a successful connection.
Printing a Network Status Sheet
To print the status sheet, hold down the network status button on the product for at least seven seconds.
Note: If you release the button before seven seconds elapses, a network connection report is printed instead of a network status sheet.
Disabling Wi-Fi Features
1. Turn off the product.
2. Hold down the network status button and press the power button until the Wi-Fi light and
Wi-Fi Direct light flash alternately. Then release both buttons.
When the Wi-Fi light and Wi-Fi Direct light turn off, Wi-Fi is disabled.
Copying
To make more than one copy, repeatedly press the B&W copy button or the color copy
button for the number of copies you need (up to 20 copies). For example, to make 4 copies, press
the button four times. Make sure you press the button in intervals of less than one second. The product scans and prints your copy.
Printer Services Channel will show you about the Printers: Printer Review or Unboxing . How to Install Driver printer, Setup printer, Maintenance Replace ink or Toner cartridge, and How to repair printer problem. Please enjoy watching that can help you now or future and Please Like Share Subscribe Hit Bell and leave Comment if have the Problem.
You can check the print head nozzles using the buttons on your product.
1. Press the power button to turn the product off.
2. Load a few sheets of plain paper in the product.
3. Hold down the stop button and press the power button to turn the product on.
4. When the product turns on, release both buttons.
The product prints a nozzle check pattern.
Print Head Cleaning
If print quality has declined and the nozzle check pattern indicates clogged nozzles, you can clean the print head. You may not be able to clean the print head when the ink level in any of the tanks is low. You may
have to refill the ink tank first.
You can clean the print head using the buttons on your product.
1. Make sure no product lights are indicating errors.
2. Load a few sheets of plain paper in the product.
3. Hold down the stop button for five seconds to start the cleaning cycle.
The power light flashes throughout the cleaning cycle and stays on when the cleaning cycle is
finished.
Caution: Never turn off the product during a cleaning cycle or you may damage it.
4. Run a nozzle check to confirm that the print head is clean.
5. Do one of the following:
• If there are no gaps, the print head is clean and you can continue printing.
• If there are gaps or the pattern is faint, clean the print head.
If you don’t see any improvement after cleaning the print head up to 3 times, turn off the product and wait
at least 12 hours. Then try cleaning the print head again. If quality still does not improve, run a Power
Cleaning
Press and hold the stop button for 5 seconds until the power light starts to blink and ink charging begins, Enabling Wi-Fi Direct Mode You can enable Wi-Fi Direct mode to allow direct communication between your product and computer or other devices without a wireless router or access point,
1. Hold down the Wi-Fi button and press the network status button until the Wi-Fi light and WiFi Direct light flash alternately. Then release both buttons.
After both lights stop flashing, the Wi-Fi Direct light remains on.
2. Hold down the network status button for about seven seconds to print a network status sheet.
3. Use your computer or wireless device to select the Wi-Fi network name (SSID) and password listed
in the Wi-Fi Direct section of the network status sheet.
You should now be able to print to your product directly from your computer or device. If you cannot
print successfully, repeat the process above and make sure you enter the password exactly as written on the network status sheet.
Using WPS to Connect to a Network
If you have a WPS-enabled router or access point, you can use Wi-Fi Protected Setup (WPS) to connect your device to the network.
1. Press the WPS button on your router or access point.
2. Hold down the Wi-Fi button on your product for about five seconds until the Wi-Fi light and WiFi Direct light flash alternately.
The Wi-Fi light turns green to indicate a successful connection.
Printing a Network Status Sheet
To print the status sheet, hold down the network status button on the product for at least seven seconds.
Note: If you release the button before seven seconds elapses, a network connection report is printed instead of a network status sheet.
Disabling Wi-Fi Features
1. Turn off the product.
2. Hold down the network status button and press the power button until the Wi-Fi light and
Wi-Fi Direct light flash alternately. Then release both buttons.
When the Wi-Fi light and Wi-Fi Direct light turn off, Wi-Fi is disabled.
Copying
To make more than one copy, repeatedly press the B&W copy button or the color copy
button for the number of copies you need (up to 20 copies). For example, to make 4 copies, press
the button four times. Make sure you press the button in intervals of less than one second. The product scans and prints your copy.
Printer Services Channel will show you about the Printers: Printer Review or Unboxing . How to Install Driver printer, Setup printer, Maintenance Replace ink or Toner cartridge, and How to repair printer problem. Please enjoy watching that can help you now or future and Please Like Share Subscribe Hit Bell and leave Comment if have the Problem.
2 سال پیش
در تاریخ 1401/09/04 منتشر شده
است.
1,103
بـار بازدید شده