Comtrend 9020 Powerline Ethernet Adapters - How To Factory Reset / Configure
115.8 هزار بار بازدید -
12 سال پیش
-
Written Instruction Included Below:- To
Written Instruction Included Below:-
To set up the adapters which, to function correctly, must be paired (One AP, One EP):-
1/ Plug both adapters into a double mains power socket side by side or somewhere so you can see/access both adapters.
2/ (00:00) First, factory reset both adapters (which will turn them both into EP's):-
Whilst plugged into the mains power, press and hold the 'Config/Reset' button for TEN seconds (or, until the 'Status' LED turns Red and extinguishes), then release the button. Wait 30 seconds for the LED's to settle.
3/ (00:43) Now, decide which adapter will be the AP (Ideally the adapter with the serial ending in 'A'):- On your chosen AP adapter, press and hold the hold the 'Config/Reset' button for FIVE seconds (or, until the 'AP' LED flashes Green), then release the button. Wait 30 seconds for the LED's to settle.
4/ (01:30) Finally, on the chosen AP adapter, press and hold the hold the 'Config/Reset' white button for FIVE seconds (or, until the 'AP' LED flashes Green), release the button, while the 'Green' AP LED is flashing (on the AP adapter), go to the EP adapter and press/hold to the 'Config/Reset' button for FIVE seconds (or, until the 'AP' LED flashes Green), then release the button.
(01:58) You will notice when you release the button the 'AP' LED on the EP adapter will flash Green three times quickly to verify the configuration change.
5/ (02:14) After 30 seconds and the LED's have settled on both units. You should now see:-
On the AP adapter,
AP LED: Green
Status LED: Green
On the EP adapter,
AP LED: Unlit
Status LED: Green
You now have two adapters:
1- AP (or Access Point) This is the adapter which must be plugged into your router/modem with the serial number ending with 'A'
2 - EP (or End Point) This adapter is plugged into your end point or destination.
=========================================================
To set up the adapters which, to function correctly, must be paired (One AP, One EP):-
1/ Plug both adapters into a double mains power socket side by side or somewhere so you can see/access both adapters.
2/ (00:00) First, factory reset both adapters (which will turn them both into EP's):-
Whilst plugged into the mains power, press and hold the 'Config/Reset' button for TEN seconds (or, until the 'Status' LED turns Red and extinguishes), then release the button. Wait 30 seconds for the LED's to settle.
3/ (00:43) Now, decide which adapter will be the AP (Ideally the adapter with the serial ending in 'A'):- On your chosen AP adapter, press and hold the hold the 'Config/Reset' button for FIVE seconds (or, until the 'AP' LED flashes Green), then release the button. Wait 30 seconds for the LED's to settle.
4/ (01:30) Finally, on the chosen AP adapter, press and hold the hold the 'Config/Reset' white button for FIVE seconds (or, until the 'AP' LED flashes Green), release the button, while the 'Green' AP LED is flashing (on the AP adapter), go to the EP adapter and press/hold to the 'Config/Reset' button for FIVE seconds (or, until the 'AP' LED flashes Green), then release the button.
(01:58) You will notice when you release the button the 'AP' LED on the EP adapter will flash Green three times quickly to verify the configuration change.
5/ (02:14) After 30 seconds and the LED's have settled on both units. You should now see:-
On the AP adapter,
AP LED: Green
Status LED: Green
On the EP adapter,
AP LED: Unlit
Status LED: Green
You now have two adapters:
1- AP (or Access Point) This is the adapter which must be plugged into your router/modem with the serial number ending with 'A'
2 - EP (or End Point) This adapter is plugged into your end point or destination.
=========================================================
12 سال پیش
در تاریخ 1391/03/16 منتشر شده
است.
115,865
بـار بازدید شده