Монтаж на контакт за външен монтаж?
3.8 هزار بار بازدید -
3 سال پیش
-
How to properly install a
How to properly install a socket for outdoor installation?
Hello, I am Yosif and this is the electro old channel as you know the channel is still developing so each of you who subscribes helps a lot for its development.
Thank you!
And as you know, at the end of each month I make a raffle in which I draw one of all subscribe to the channel and activated the option to see them as such and send him a T-shirt on the channel and some insulated screwdrivers up to 1000 volts.
So subscribe and good luck
At this link you can subscribe to the channel:
@electrostar_bg
In this video I will show you how to properly install a socket for outdoor installation.
To begin with, we must have a socket that is designed for outdoor installation, which is flat at the back and does not need a bracket for its installation.
Then we need to determine what our two-wire or three-wire network is
As we know, with a two-wire electrical network we have to make a bridge between the zero and the earth pins, thus we make a protective zero. And with a three-wire installation we install phase, zero and in the middle of the pins we install the earth conductor.
Once we determine what kind of installation we have, we need to physically mount the key to the wall, in this case I will install this socket for outdoor installation using dowel nails.
Since the wires are in the wall, it is necessary to check with a metal detector or voltage detector where the wires go so that it does not happen so that we make holes on them.
After doing this check, we can now start drilling holes in the wall.
We mount the socket to the wall and lead the wires to the connection terminals.
We connect the blue wire which in this case is zero to the zero terminal and by means of a bridge of the same square we connect the other end of the bridge to the ground pins.
This is followed by the installation of the brown wire to the phase terminal.
After tightening the connections well, we check them by hand and proceed to the installation of the decorative cap.
Once the electrical installation of the socket is ready, we must restore the voltage and check the socket.
We check in this case with a multimeter in both holes and there are 242 volts.
We check and the phase to the ground terminal also has 242 volts
During such a check, care must be taken to ensure that the phase conductor is not accidentally connected to the earth terminals.
Also, some of these videos can be very useful to you:
Fallen battery what to do:
Паднал акумулатор,какво да направим ?
Installation of contact in a plasterboard wall:
Монтаж на контакт във стена от гипсок...
Installation of single contact indoor installation:
Монтаж на единичен контакт вътрешен м...
Installation of a switch for lighting double:
Монтаж на ключ за осветление двоен.
Contact installation and zeroing:
Монтаж на контакт и зануляване?
What should be in the suitcase of an electrician:
Какво трябва да има в куфара на един ...
At this link you can subscribe to the channel:
@electrostar_bg
Hello, I am Yosif and this is the electro old channel as you know the channel is still developing so each of you who subscribes helps a lot for its development.
Thank you!
And as you know, at the end of each month I make a raffle in which I draw one of all subscribe to the channel and activated the option to see them as such and send him a T-shirt on the channel and some insulated screwdrivers up to 1000 volts.
So subscribe and good luck
At this link you can subscribe to the channel:
@electrostar_bg
In this video I will show you how to properly install a socket for outdoor installation.
To begin with, we must have a socket that is designed for outdoor installation, which is flat at the back and does not need a bracket for its installation.
Then we need to determine what our two-wire or three-wire network is
As we know, with a two-wire electrical network we have to make a bridge between the zero and the earth pins, thus we make a protective zero. And with a three-wire installation we install phase, zero and in the middle of the pins we install the earth conductor.
Once we determine what kind of installation we have, we need to physically mount the key to the wall, in this case I will install this socket for outdoor installation using dowel nails.
Since the wires are in the wall, it is necessary to check with a metal detector or voltage detector where the wires go so that it does not happen so that we make holes on them.
After doing this check, we can now start drilling holes in the wall.
We mount the socket to the wall and lead the wires to the connection terminals.
We connect the blue wire which in this case is zero to the zero terminal and by means of a bridge of the same square we connect the other end of the bridge to the ground pins.
This is followed by the installation of the brown wire to the phase terminal.
After tightening the connections well, we check them by hand and proceed to the installation of the decorative cap.
Once the electrical installation of the socket is ready, we must restore the voltage and check the socket.
We check in this case with a multimeter in both holes and there are 242 volts.
We check and the phase to the ground terminal also has 242 volts
During such a check, care must be taken to ensure that the phase conductor is not accidentally connected to the earth terminals.
Also, some of these videos can be very useful to you:
Fallen battery what to do:
Паднал акумулатор,какво да направим ?
Installation of contact in a plasterboard wall:
Монтаж на контакт във стена от гипсок...
Installation of single contact indoor installation:
Монтаж на единичен контакт вътрешен м...
Installation of a switch for lighting double:
Монтаж на ключ за осветление двоен.
Contact installation and zeroing:
Монтаж на контакт и зануляване?
What should be in the suitcase of an electrician:
Какво трябва да има в куфара на един ...
At this link you can subscribe to the channel:
@electrostar_bg
3 سال پیش
در تاریخ 1400/11/24 منتشر شده
است.
3,808
بـار بازدید شده