XIKAR Resource Pipe Lighter Review
3.6 هزار بار بازدید -
9 سال پیش
-
XIKAR Resource Pipe LighterPipe Smokers
XIKAR Resource Pipe Lighter
Pipe Smokers - Never be stuck without the necessary pipe smoking tools again. The new XIKAR Pipe Lighter comes equipped with everything you need neatly tucked away in the body of the lighter. From the top of the bowl to the bottom you have a stainless steel tamper, poker and knife ready and at your disposal. The durable lighter ignites with a simple pull-back ignition to reveal an angled candle flame.
Instructions for Use
Lighters: XIKAR Lighter Ignited
IGNITING THE LIGHTER • A simple push on the ignition switch ignites a powerful
flame over 2,000 degrees. This flame can be nearly invisible in
bright light, so proper care is recommended.
TAKE CARE NOT TO TOUCH THE LIGHTER TOP AFTER IGNITION. • To avoid heat buildup, do not use in any situation that would
require a continuous flame for more than 10 seconds. The lighter
may become too hot and cause harm to the lighter and/or the user.
EXTINGUISHING THE FLAME • Releasing pressure from the ignition button of the lighter
immediately extinguishes the flame by stopping fuel flow.
If flame continues, the flame level is set too high and should be
adjusted by turning the adjustment wheel on the bottom of the
lighter towards the (-) position.
ADJUSTING FLAME LEVEL • Turn the fuel adjustment wheel on the bottom of the lighter
towards the (+) mark to increase the flame and turn the wheel
towards the (-) to decrease the flame to achieve a desired height.
FILLING AND RE-FILLING LIGHTERLighter Bleeding with XIKAR MTX Tool 1. Release all tank pressure by pressing on the inlet valve with a small
screwdriver or a XIKAR MTX Multi Tool bleeder (shown). Hold the
lighter vertical while bleeding valve. Repeat this several times until all
fuel/ gas pressure is released.
2. Set flame adjustment to lowest setting (-).
3. Turn lighter in upside down position and insert butane tank tip directly
on the fuel valve. Do not shake the can of butane! This increases the amount
of propellent in the mixture that goes into the lighter, and should not be done.
Press down firmly for about 5 seconds.
4. Before igniting lighter, wait 3-4 minutes. This allows excess butane to
evaporate and gas inside lighter to reach room temperature.
5. Set flame level to desired height by turning flame adjuster wheel.
Pipe Smokers - Never be stuck without the necessary pipe smoking tools again. The new XIKAR Pipe Lighter comes equipped with everything you need neatly tucked away in the body of the lighter. From the top of the bowl to the bottom you have a stainless steel tamper, poker and knife ready and at your disposal. The durable lighter ignites with a simple pull-back ignition to reveal an angled candle flame.
Instructions for Use
Lighters: XIKAR Lighter Ignited
IGNITING THE LIGHTER • A simple push on the ignition switch ignites a powerful
flame over 2,000 degrees. This flame can be nearly invisible in
bright light, so proper care is recommended.
TAKE CARE NOT TO TOUCH THE LIGHTER TOP AFTER IGNITION. • To avoid heat buildup, do not use in any situation that would
require a continuous flame for more than 10 seconds. The lighter
may become too hot and cause harm to the lighter and/or the user.
EXTINGUISHING THE FLAME • Releasing pressure from the ignition button of the lighter
immediately extinguishes the flame by stopping fuel flow.
If flame continues, the flame level is set too high and should be
adjusted by turning the adjustment wheel on the bottom of the
lighter towards the (-) position.
ADJUSTING FLAME LEVEL • Turn the fuel adjustment wheel on the bottom of the lighter
towards the (+) mark to increase the flame and turn the wheel
towards the (-) to decrease the flame to achieve a desired height.
FILLING AND RE-FILLING LIGHTERLighter Bleeding with XIKAR MTX Tool 1. Release all tank pressure by pressing on the inlet valve with a small
screwdriver or a XIKAR MTX Multi Tool bleeder (shown). Hold the
lighter vertical while bleeding valve. Repeat this several times until all
fuel/ gas pressure is released.
2. Set flame adjustment to lowest setting (-).
3. Turn lighter in upside down position and insert butane tank tip directly
on the fuel valve. Do not shake the can of butane! This increases the amount
of propellent in the mixture that goes into the lighter, and should not be done.
Press down firmly for about 5 seconds.
4. Before igniting lighter, wait 3-4 minutes. This allows excess butane to
evaporate and gas inside lighter to reach room temperature.
5. Set flame level to desired height by turning flame adjuster wheel.
9 سال پیش
در تاریخ 1394/05/23 منتشر شده
است.
3,632
بـار بازدید شده