How to mix and apply Surfacelogix Cobble Loc - 2 part kit
15.6 هزار بار بازدید -
6 سال پیش
-
Learn how to apply Surfacelogix
Learn how to apply Surfacelogix Cobble Loc in less than a minute. SurfaceLogix Cobble Loc is the newest technology in waterborne protection for concrete, brick pavers and surfaces decorated with our Texture Deck. Cobble Loc may be used over most porous surfaces as it has excellent water and marking resistance. Unlike other clear finishes, SurfaceLogix Cobble Loc has excellent resistance to brake fluid, gasoline, bleach and acids. SurfaceLogix Cobble Loc also helps lock joint sand in place. Cobble Loc is ideal for driveways, pool decks, entryways, walkways, median strips and patios. Cobble Loc is not recommended for pavers installed over a solid surface or on surfaces where moisture is unable to dissipate. Cobble Loc is an eco-friendly sealer and emits very low VOCs. Cobble Loc was designed for pressure cleaning and sealing in the same day. 1 gallon covers 200 to 300 square feet per coat. Coverage depends on the surface porosity, joint width and application method. Usually, the second coat takes slightly less product.
Curing Information:
Dry to Touch: 2-6 hours (varies with weather conditions)
Recoat: 2-6 hours
Full Cure: 48-72 Hours
Directions:
Before You Begin: Surfaces must be clean and free of any contaminants before sealing. Cobble Loc’s performance is directly related to how thoroughly the surfaced is prepared. Do not apply when the temperature of the air or the surface to be coated is below 50°F. Testing on your surface is always recommended to ensure desired results.
Surface Preparation: Smooth concrete must be etched. Scrape and sand all loose material prior to application. Cobble Clean, Cobble Prep and Cobble Oxhide may be used for specific cleaning situations.
Mixing Instructions: Cobble Loc is a two component kit. Part A must be mixed with Part B. A 1 gallon kit includes a quart of Part B & a 5 gallon kit includes a short filled 5 gallon pail and a one gallon pail of Part B. Dilute Cobble Loc with one part water with one part mixed sealer. For best results, it is recommended to mechanically mix with a power mixer for a minimum of 2 - 5 minutes.
Applications Roller: Apply with a 3/8” to 3/4” nap roller cover
Airless Sprayer: Spray by overlapping each pass. Always apply in an even film deposit and maintain a working wet line. On Bare Surface: One and sometimes two thin coats (2 dry mils) provide the best results on uncoated surfaces. Over Previously Sealed: One coat is recommended
Storage and Shelf Life:
Product must be kept in its original, unopened and tightly sealed container. Store in a dry and well ventilated place with controlled temperature (50°F to 90°F). Keep sheltered from weather and direct sunlight. In proper storage conditions, the product’s shelf life is 12 months following production (see date on packaging). Store product in original container and close lid tightly after each use.
Clean Up: Clean sprayer and tools with water and SurfaceLogix Reducer immediately after use. Flush water though the line of the sprayer until clear. Leave SurfaceLogix Reducer in the line of machine after flushing with water.
Disclaimer: All SurfaceLogix products are manufactured with the finest raw materials. It is the applicator's responsibility to determine the appropriate use of the product.
All recommendations and suggestions are made without guarantee, since conditions of use are beyond our control.
Curing Information:
Dry to Touch: 2-6 hours (varies with weather conditions)
Recoat: 2-6 hours
Full Cure: 48-72 Hours
Directions:
Before You Begin: Surfaces must be clean and free of any contaminants before sealing. Cobble Loc’s performance is directly related to how thoroughly the surfaced is prepared. Do not apply when the temperature of the air or the surface to be coated is below 50°F. Testing on your surface is always recommended to ensure desired results.
Surface Preparation: Smooth concrete must be etched. Scrape and sand all loose material prior to application. Cobble Clean, Cobble Prep and Cobble Oxhide may be used for specific cleaning situations.
Mixing Instructions: Cobble Loc is a two component kit. Part A must be mixed with Part B. A 1 gallon kit includes a quart of Part B & a 5 gallon kit includes a short filled 5 gallon pail and a one gallon pail of Part B. Dilute Cobble Loc with one part water with one part mixed sealer. For best results, it is recommended to mechanically mix with a power mixer for a minimum of 2 - 5 minutes.
Applications Roller: Apply with a 3/8” to 3/4” nap roller cover
Airless Sprayer: Spray by overlapping each pass. Always apply in an even film deposit and maintain a working wet line. On Bare Surface: One and sometimes two thin coats (2 dry mils) provide the best results on uncoated surfaces. Over Previously Sealed: One coat is recommended
Storage and Shelf Life:
Product must be kept in its original, unopened and tightly sealed container. Store in a dry and well ventilated place with controlled temperature (50°F to 90°F). Keep sheltered from weather and direct sunlight. In proper storage conditions, the product’s shelf life is 12 months following production (see date on packaging). Store product in original container and close lid tightly after each use.
Clean Up: Clean sprayer and tools with water and SurfaceLogix Reducer immediately after use. Flush water though the line of the sprayer until clear. Leave SurfaceLogix Reducer in the line of machine after flushing with water.
Disclaimer: All SurfaceLogix products are manufactured with the finest raw materials. It is the applicator's responsibility to determine the appropriate use of the product.
All recommendations and suggestions are made without guarantee, since conditions of use are beyond our control.
6 سال پیش
در تاریخ 1397/04/04 منتشر شده
است.
15,665
بـار بازدید شده