3 Ways to FIX O3 Air Unit Thermal Shutdown - STOPS RECORDING if TOO HOT! DJI O3 Air Unit Cooling
1.8 هزار بار بازدید -
10 ماه پیش
-
Thanks to PCBWay for sponsoring
Thanks to PCBWay for sponsoring this video. Check out https://www.pcbway.com/ for custom printed circuit boards, electronics, and rapid prototyping services (Use my referral link to get $5 of New User Free Credit) https://www.pcbway.com/setinvite.aspx... !
Once again I am disappointed (burned, even) by DJI. The DJI O3 Air unit does not have sufficient cooling for my needs. I found that adding aluminum cooling fins and a small fan will allow the air unit to record in 4K 60fps for about 5min before it stops due to overheating.
Does this overheating problem affect you also? Which cooling method will you use?
BLUF 00:00
Check out PCBWay 00:10
Why is overheating a problem? 1:14
Test results 3:37
One solution 5:43
-------------
🧠 FREE RESOURCES, 3D Printable Designs, and more for FPV Drones, RC Aircraft & 3D Printing at http://rcwithadam.com/
Want to support RCwithAdam? ↴
KO-FI: https://ko-fi.com/rcwithadam
OR
PATREON: Patreon: RCwithAdam
Thanks!
-------
Mandatory Affiliate Disclaimer:
Any links in this description may be affiliate links, which means I make a very small commission (at no additional cost to you) when you make a purchase through that link.
*DISCLAIMER: Remember to always use caution and your best judgement when building and flying RC aircraft, and when working with 3D printers, electronics, or electrical devices. Be mindful of the laws, regulations, and best practices for your particular location. Be a good neighbor, and HAVE FUN!*
-----------
About RCwithAdam: Adam's goal is to HELP YOU build your skills and eliminate frustration and confusion through creative, educational, and encouraging videos featuring Radio Control airplanes, FPV drones, electronics, and 3D printing!
#RCwithAdam #fpvdrone #DJI
Once again I am disappointed (burned, even) by DJI. The DJI O3 Air unit does not have sufficient cooling for my needs. I found that adding aluminum cooling fins and a small fan will allow the air unit to record in 4K 60fps for about 5min before it stops due to overheating.
Does this overheating problem affect you also? Which cooling method will you use?
BLUF 00:00
Check out PCBWay 00:10
Why is overheating a problem? 1:14
Test results 3:37
One solution 5:43
-------------
🧠 FREE RESOURCES, 3D Printable Designs, and more for FPV Drones, RC Aircraft & 3D Printing at http://rcwithadam.com/
Want to support RCwithAdam? ↴
KO-FI: https://ko-fi.com/rcwithadam
OR
PATREON: Patreon: RCwithAdam
Thanks!
-------
Mandatory Affiliate Disclaimer:
Any links in this description may be affiliate links, which means I make a very small commission (at no additional cost to you) when you make a purchase through that link.
*DISCLAIMER: Remember to always use caution and your best judgement when building and flying RC aircraft, and when working with 3D printers, electronics, or electrical devices. Be mindful of the laws, regulations, and best practices for your particular location. Be a good neighbor, and HAVE FUN!*
-----------
About RCwithAdam: Adam's goal is to HELP YOU build your skills and eliminate frustration and confusion through creative, educational, and encouraging videos featuring Radio Control airplanes, FPV drones, electronics, and 3D printing!
#RCwithAdam #fpvdrone #DJI
10 ماه پیش
در تاریخ 1402/06/30 منتشر شده
است.
1,892
بـار بازدید شده