DEAD e-bike ? Found the cause of dead e-bike VANMOOF S3/X3 Error 6 , 17 , 19 , 20 , 21

Hello guys thanks for watching..

Also I'm trying to make a channel regarding problems like this
if you have any suggestions or challenges for me I'm happy to try solving them :)
if my videos help your business and you will like to help back with a donation  or simply get in touch please do so on  [email protected] (PayPal) also don't hesitate to contact us
Razspareparts UK


this is the full list of errors to your S3/X3 Bike 🚲

Here are the battery-related
errors for the VanMoof S3:
1. BAT SCP: Short circuit
protection (main battery
related)
2. BAT_ MOTP: Mosfet over
temperature protection (main
battery related)
3. BAT_PDSCP: Pre discharge
short circuit protection (main
battery related)
4.BAT_PDOCP: Pre discharge
overload circuit protection
(main battery related)
5. BAT_UVP2: Under voltage
protection 2 (main battery
related) (try charging for a
longer period, could solve
issue)
6. BAT_UVP1: Under voltage
protection 1 (main battery
related)
7. BAT_ OVP2: Over voltage
protection 2 (main battery
related)
BAT_OVP1: Over voltage
protection 1 (main battery
related)
BAT_COCP1: Charge over
current protection 1 (main
battery related)
BAT COCP2: Charge over
current protection 2 (main
battery related)
BAT DOCP2: Discharge
Over current protection 2 (main
battery related)
BAT DOCP1: Discharge
Over curent protection 1 (main
battery related)
BAT_CUTP: Charge under
temperature protection (main
battery related) (it's too cold to
charge)
BAT COTP: Charge over
temperature protection (main
battery related) (it's too warm
to charge)
BAT DUTP: Discharge
under temperature protection
(main battery related) (it's too
cold to discharge)
BAT DOTP: Discharge over
temperature protection (main
battery related) (it's too hot to
discharge)
BATFP: Permnanent fail
(fuse burn) (main battery
related) (likely socket short
circuit)
Error 17:
BATTERY_ NO_DSG - Could
not set discharge mode (main
battery related)
Error 18:
BATTERY_MISSING - Signal
bat_key_in is low (main battery
related) (battery not
recognized, also the error you
get when no battery is present)
Error 19:
BATTERY COMMUNICATION
- Modbus battery (main battery
related)
Error 20:
- BMS
seems to shutdown (main
battery related)
22. Error 21:
NO_ CHARGE_CURRENT
Charging state but no current
reported (main battery related)

Transfer from app aborted
(Module related) (Upload was
aborted?)
Error 25: OAD_ CRC -
Transferred image crc error
(Module related)
Error 26:
- OAD file transfer took too
long (Module related)
Error 27: OAD_PACK - No
or invalid file in pack (Module
related)
Error 28: ICF_TIMEOUT -
Timeout during flash
programming (Module related)
HEADER -
Error 29: ICF
Header not found (Module
related)
Error 30: \CF_ NO_FILES -
No files in pack (Module
related)
Error 31: ICF ERASE -
Flash erase error (Module
related)
Error 32: ICF WRITE -
Flash write error (Module
related)
Error 33: ICF CRC - File in
pack has CRC error (Module
related)
Error 34 -
Programming of the motor
Controller failed
. Error 35:
PGM_BATTERYWARE -
Programming of the BMS
Controller failed
Error 36:
PGM_SHIFTERWARE -
Programming of the shifter
Controller failed  Error 37: PGM_BLEWARE -
Programming of the BLE
Controller failed
Error 38: -
STVC3115 read error, LiPo
might be missing (Module
related) (check if battery
m o io hor)
Error 39:
READ_LIGHT
_SENSOR
CM3232 12C read u - Kick-
Lock coil not detected
Error 43:
SHIFTER_NOT_IN_GEAR -
After 10 tries, gear has not
been reached
Error 44:
SHIFTER
COMMUNICATION -
Modbus Shifter (Shifter not
recognized) (Plug in tester
Shifter)
Error 45:
MOTOR MOTOR CABLE -
Bit2/NTC motor cable not
Connected (Motor not
recognized)
4mError 46:
MOTOR MOTOR_OVER CURRENT
- DRV8301 over temperature
(bit6)
Error 48:
MOTOR CONTROLLER_ERROR
- Error in user parameters
(bit8) (replace motor)
Error 49:
MOTOR CURRENT_ERR -
Current offset calculation +-
from default value 1.0
Error 50:
MOTOR_VOLTAGE_ERR -
Voltage offset calculation
+*from Vbat/2 or Vbat
Error 51:
MOTOR_ DERATING - Max
current limited due to high
temp
Error 52:
MOTOR TORQUE_SENSOR FAIL
- Torque sensor failed, only if
sensor required
Error 53:
MOTOR NOT READY - Motor
not ready during motor test or
error
Error 54: NO SIMCARD -
SIM card not present (Module
related) (SIM not recognized)
Error 55: 12C3_FAIL -
Started with l2C error on bus
Error 56: CCID_SIMCARD -
SIM card wrong CCID
(VanMoof) number
Error 57: READ_SIMCARD -
SIM card is detected but no
communication (Module
related) (Check ICCD number
in BO)
Error 58: GSM_MODEM -
Modem startup sequence
failed (Module related) (often
gone after reset)
Error 60: FACTORY_MODE
- Display 60 when factory

hope it helps ☺️