How to Lubricate a Window Regulator or Mechanism using DeoxIT
60.7 هزار بار بازدید -
5 سال پیش
-
How to lubricate a slow
How to lubricate a slow window mechanism in your vehicle, this applies both to manual & power windows. Over time the existing lubricant can become contaminated with dirt, loosing it’s lubrication qualities, and eventually cause excessive wear on certain components. Once those components wear out they’ll require a replacement and depending on the vehicle, this can be costly. #deoxit #maintenance #autocare
Enter Contest: https://gleam.io/fmDgj/deoxit-x10s-pr...
Caig Cleaner: https://caig.com/product/degreaser-wa...
DeoxIT L260DNp: https://caig.com/product/new-deoxit-l...
DeoxIT X10S: https://caig.com/product/deoxit-x10s-...
Website: http://4diyers.com
Patreon: Patreon: 4diyers
Facebook: Facebook: 4diyers
Google Plus: https://plus.google.com/+4DIYers
Twitter: Twitter: 4DIYers
Instagram: Instagram: 4diyers
Tumblr: Tumblr: 4diyers
Pintrest: Pinterest: 4diyers
Tools/Supplies Needed:
-paper towel
-degreaser
-nylon trim tool
-screwdrivers
Procedure:
Remove the door panel on the vehicle. First is a 2001 Toyota Tacoma. As a rough overview, locate any fasteners which may need to be removed. Here there are two phillips screws hiding behind plastic caps which are removed. Pop up the window switches, disconnect the wires on the rear.
The door handle also has a phillips screw that needs to be removed. Then the handle will need to be slide forward to disconnect it from the door. Remove the cap up by the mirror area. Unclip the panel from the door.
Disconnect any wires in the rear & push the door handle through the panel. Doors typically have a vapor barrier in behind the panel as a form of protection against moisture. This just pulls away, they’re usually held on with butyl tape.
I also removed the door speaker to help gain more access inside the door. The window switches were reconnected, turn on the key & then operate the window. Once you have it in a workable position, turn the ignition off and remove the keys. When the mechanism is moving, do not stick your fingers anywhere near it. Once it’s in the right spot, remove the key. Some vehicles can still have their windows operated for a few minutes when the key is removed, so press the window switches again to determine if this is the case or disconnect the window switches.
Using a cleaner from Caig Laboratories Val-U series, model number is DDW-V611. This can be applied to paper towel, a rag or lightly sprayed to clean away the old lubricant or dirt. Use DeoxIT’s L260D grease, apply this within the track, both on the bottom and top where the wheels ride. You should be able to see wear marks where the mechanism runs, grease needs to cover these areas.
Now moving the window up & gaining access to the half moon gear. Again using the degreaser & paper towel, clean away the old grease. Finally apply new grease to the gear. Clean the rubber tracks on each side of the window. Using a brush, either a detailing or toothbrush with a vacuum, clean the rubber tracks.
Use DeoxIT’s X10S Precision Lubricant apply a couple drops to the inside of the tracks. Only do this on the vertical tracks.
Once done, reinstall all the parts in reverse of removal.
For a 1998 Ford Ranger, this time around this has a manual window. First removing any screws in the panel. This particular window crank requires the cap to be popped off and a torx screw is hidden in behind. Remove the trim piece on the door panel using a nylon trim tool. Disconnect the power mirror connector. There is one screw hidden in behind this panel. Pull the panel straight up & remove.
Pull the vapor barrier back to gain access to the window regular. The window crank can be slid back on to operate the regulator. Use Caig Laboratories Val-U series degreaser, apply it to a paper towel & remove the old grease. For the half moon gear, clean it using paper towel & a degreaser. If this were a power window, DO NOT STICK your fingers anywhere near the mechanism. You can get severely hurt if your fingers get caught in the mechanism. Use a vacuum & brush to clean the vertical rubber tracks. Apply DeoxIT’s X10S Precision Lubricant to only the vertical rubber tracks. Apply DeoxIT’s L260D grease to the metal tracks inside the door, both the horizontal & vertical mechanism. Apply grease to the half moon gear.
Once done, reinstall all the parts in reverse of removal.
Thank you to all those who watch my videos and support my content. Don't forget to subscribe to my channel for future tutorial videos and like my video if you found it helpful. New videos are always being uploaded every week!
© 4DIYers 2013
All Rights Reserved
No part of this video or any of its contents may be reproduced, copied, modified or adapted, without the prior written consent of the author.
Enter Contest: https://gleam.io/fmDgj/deoxit-x10s-pr...
Caig Cleaner: https://caig.com/product/degreaser-wa...
DeoxIT L260DNp: https://caig.com/product/new-deoxit-l...
DeoxIT X10S: https://caig.com/product/deoxit-x10s-...
Website: http://4diyers.com
Patreon: Patreon: 4diyers
Facebook: Facebook: 4diyers
Google Plus: https://plus.google.com/+4DIYers
Twitter: Twitter: 4DIYers
Instagram: Instagram: 4diyers
Tumblr: Tumblr: 4diyers
Pintrest: Pinterest: 4diyers
Tools/Supplies Needed:
-paper towel
-degreaser
-nylon trim tool
-screwdrivers
Procedure:
Remove the door panel on the vehicle. First is a 2001 Toyota Tacoma. As a rough overview, locate any fasteners which may need to be removed. Here there are two phillips screws hiding behind plastic caps which are removed. Pop up the window switches, disconnect the wires on the rear.
The door handle also has a phillips screw that needs to be removed. Then the handle will need to be slide forward to disconnect it from the door. Remove the cap up by the mirror area. Unclip the panel from the door.
Disconnect any wires in the rear & push the door handle through the panel. Doors typically have a vapor barrier in behind the panel as a form of protection against moisture. This just pulls away, they’re usually held on with butyl tape.
I also removed the door speaker to help gain more access inside the door. The window switches were reconnected, turn on the key & then operate the window. Once you have it in a workable position, turn the ignition off and remove the keys. When the mechanism is moving, do not stick your fingers anywhere near it. Once it’s in the right spot, remove the key. Some vehicles can still have their windows operated for a few minutes when the key is removed, so press the window switches again to determine if this is the case or disconnect the window switches.
Using a cleaner from Caig Laboratories Val-U series, model number is DDW-V611. This can be applied to paper towel, a rag or lightly sprayed to clean away the old lubricant or dirt. Use DeoxIT’s L260D grease, apply this within the track, both on the bottom and top where the wheels ride. You should be able to see wear marks where the mechanism runs, grease needs to cover these areas.
Now moving the window up & gaining access to the half moon gear. Again using the degreaser & paper towel, clean away the old grease. Finally apply new grease to the gear. Clean the rubber tracks on each side of the window. Using a brush, either a detailing or toothbrush with a vacuum, clean the rubber tracks.
Use DeoxIT’s X10S Precision Lubricant apply a couple drops to the inside of the tracks. Only do this on the vertical tracks.
Once done, reinstall all the parts in reverse of removal.
For a 1998 Ford Ranger, this time around this has a manual window. First removing any screws in the panel. This particular window crank requires the cap to be popped off and a torx screw is hidden in behind. Remove the trim piece on the door panel using a nylon trim tool. Disconnect the power mirror connector. There is one screw hidden in behind this panel. Pull the panel straight up & remove.
Pull the vapor barrier back to gain access to the window regular. The window crank can be slid back on to operate the regulator. Use Caig Laboratories Val-U series degreaser, apply it to a paper towel & remove the old grease. For the half moon gear, clean it using paper towel & a degreaser. If this were a power window, DO NOT STICK your fingers anywhere near the mechanism. You can get severely hurt if your fingers get caught in the mechanism. Use a vacuum & brush to clean the vertical rubber tracks. Apply DeoxIT’s X10S Precision Lubricant to only the vertical rubber tracks. Apply DeoxIT’s L260D grease to the metal tracks inside the door, both the horizontal & vertical mechanism. Apply grease to the half moon gear.
Once done, reinstall all the parts in reverse of removal.
Thank you to all those who watch my videos and support my content. Don't forget to subscribe to my channel for future tutorial videos and like my video if you found it helpful. New videos are always being uploaded every week!
© 4DIYers 2013
All Rights Reserved
No part of this video or any of its contents may be reproduced, copied, modified or adapted, without the prior written consent of the author.
5 سال پیش
در تاریخ 1398/04/07 منتشر شده
است.
60,764
بـار بازدید شده