How to replace Renault Megane 2 Clutch Concentric Slave Cylinder
162.2 هزار بار بازدید -
6 سال پیش
-
So just you all know,
So just you all know, this is not easy task and will take a lot of time!
A short story of what happened, I was driving my Renault Megane 2 and suddenly I lost clutch, when I tried to push clutch pedal, it went into the floor and did pop back, but that was smallest problem, I could not change gears as well!
The easy way how to inspect if the problem is because of faulty Clutch Concentric Slave Cylinder, is by pressing the clutch pedal in and out many times and checking if oil is spilling under the car, what happened to me, the best case scenario is that u are out of brake fluid, but not in my case.
On my video I am showing how to disassemble the car, to get to the clutch cylinder, like how to remove tire support, axles, break supports, break free lower ball joint, remove front strut, remove cars computer, remove engine mount at gearbox side, remove all kind of connections, remove starter, remove sub frame, take a part gearbox from engine, etx. and put everything back together! And of course how to replace clutch cylinder and how to bleed clutch slave cylinder, what wasnt that super easy!
Any way in the end I managed in the yard replace the clutch slave cylinder and car now works very good, even better than before, so it is possible, of course you will need a lot of different tools and if you will do as I did, as well some sort of winch and 8 mm square drain plug opening tool, so you can drain gearbox oil.
Any way on the internet I found that to do this work at workshop it takes at least 4 hours + at least 30 mintues to bleed the clutch, but for me it took a lot more, since I did it for first time and to open all the bolts and to understand what to do next, that took most of the time, if I would have to do this again ( what I would not like to do :D ) it would take a lot less time, bcos I would now what to do, so I hope may video gives you some sort of help to reduce the time you spend on this!
A short story of what happened, I was driving my Renault Megane 2 and suddenly I lost clutch, when I tried to push clutch pedal, it went into the floor and did pop back, but that was smallest problem, I could not change gears as well!
The easy way how to inspect if the problem is because of faulty Clutch Concentric Slave Cylinder, is by pressing the clutch pedal in and out many times and checking if oil is spilling under the car, what happened to me, the best case scenario is that u are out of brake fluid, but not in my case.
On my video I am showing how to disassemble the car, to get to the clutch cylinder, like how to remove tire support, axles, break supports, break free lower ball joint, remove front strut, remove cars computer, remove engine mount at gearbox side, remove all kind of connections, remove starter, remove sub frame, take a part gearbox from engine, etx. and put everything back together! And of course how to replace clutch cylinder and how to bleed clutch slave cylinder, what wasnt that super easy!
Any way in the end I managed in the yard replace the clutch slave cylinder and car now works very good, even better than before, so it is possible, of course you will need a lot of different tools and if you will do as I did, as well some sort of winch and 8 mm square drain plug opening tool, so you can drain gearbox oil.
Any way on the internet I found that to do this work at workshop it takes at least 4 hours + at least 30 mintues to bleed the clutch, but for me it took a lot more, since I did it for first time and to open all the bolts and to understand what to do next, that took most of the time, if I would have to do this again ( what I would not like to do :D ) it would take a lot less time, bcos I would now what to do, so I hope may video gives you some sort of help to reduce the time you spend on this!
6 سال پیش
در تاریخ 1397/08/12 منتشر شده
است.
162,213
بـار بازدید شده