DIY Portable Skatepark (Skateboard Grind Box and Manual Pad)
9.4 هزار بار بازدید -
5 سال پیش
-
Linktree to the tools that
Linktree to the tools that I use and my other socials:
https://linktr.ee/buildsbyalexis
Check out my Etsy Store!
https://skatethencreateco.etsy.com
Music: Skate
Artist: Jef
This video shows how I made a Skate box and Manual pad fit into my Hatchback! I wanted to make this video to show that you don't need your own warehouse or a large van or SUV (or even a car) to be able to have your own mini skatepark.
UPDATE: If you are using an angle grinder to cut the coping, I recommend getting a 40 grit flap disc for the angle grinder to round the edge of the coping that you will be skating on. After skating it for a few months, I noticed my trucks were wearing down a lot faster than normal, due to the sharp edge of the coping/steel angle.
Music: Skate
Artist: Jef
Tools and Materials are below:
Ryobi power drill:
https://www.homedepot.com/p/RYOBI-18-...
Ryobi Circular saw:
https://www.homedepot.com/p/RYOBI-18-...
The angle grinder I used is several years old. But most home centers have a wide selection:
(If possible, make a box that is 6 ft or 8 ft long to avoid needing to use an angle grinder and just buy steel angles already cut at 6 ft or 8 ft.)
https://www.homedepot.com/s/angle%252...
You can also rent tools at Home Depot (Also check your local home center to see if they rent tools out if you dont have a Home Depot near you):
https://www.homedepot.com/c/tool_and_...
I used a 12-inch rafter square (but you can also get smaller ones for cheaper):
https://www.homedepot.com/p/Empire-12...
I used heavier duty clamps but you can use much cheaper clamps for cutting plywood:
(A couple of 12 inch clamps should be fine, and maybe one 24 inch or a 36 inch clamp to hold the larger pieces.)
https://www.homedepot.com/p/BESSEY-12...
https://www.homedepot.com/p/BESSEY-6-...
https://www.homedepot.com/p/DEWALT-24...
https://www.homedepot.com/p/DEWALT-12...
I used this T-Square (though you can use practically anything to guide your circular saw as long as it's straight):
https://www.homedepot.com/p/Empire-48...
You can use this trim square to help you cut 2x4s to length:
https://www.homedepot.com/p/Milwaukee...
Metal countersink drill bit:
https://www.homedepot.com/p/RYOBI-3-4...
2x4 Douglas Fir:
https://www.homedepot.com/p/2-in-x-4-...
23/32 plywood (for the walls of the skate box) :
https://www.homedepot.com/p/23-32-in-...
15/32 plywood (for the top):
https://www.homedepot.com/p/15-32-in-...
Masonite 4x8 sheet (tempered hardboard):
https://www.homedepot.com/p/Hardboard...
Masonite (2x4 sheet):
https://www.homedepot.com/p/Hardboard...
2 in. x 72 in. Angle Plain Steel with 0.125 Thick (Coping for skate box, which was cut to 60 inches with an angle grinder):
https://www.homedepot.com/p/2-in-x-72...
I used 2.5-inch coarse Drywall screws (DONT FORGET TO PREDRILL YOUR HOLES (1/8th inch drill bit should be good.):
https://www.homedepot.com/p/Grip-Rite...
Cheaper, decent furniture dolly:
https://www.homedepot.com/p/Milwaukee...
Better quality furniture dolly:
https://www.uline.com/Product/Detail/...
You could also potentially make your own using scrap 2x4s and buy some 4 inch casters
https://www.homedepot.com/p/Everbilt-...
Comment down below if you have any questions!
Jukin Media Verified
Interested in licensing this footage?
Learn more @ https://www.jukinmedia.com/licensing/...
https://linktr.ee/buildsbyalexis
Check out my Etsy Store!
https://skatethencreateco.etsy.com
Music: Skate
Artist: Jef
This video shows how I made a Skate box and Manual pad fit into my Hatchback! I wanted to make this video to show that you don't need your own warehouse or a large van or SUV (or even a car) to be able to have your own mini skatepark.
UPDATE: If you are using an angle grinder to cut the coping, I recommend getting a 40 grit flap disc for the angle grinder to round the edge of the coping that you will be skating on. After skating it for a few months, I noticed my trucks were wearing down a lot faster than normal, due to the sharp edge of the coping/steel angle.
Music: Skate
Artist: Jef
Tools and Materials are below:
Ryobi power drill:
https://www.homedepot.com/p/RYOBI-18-...
Ryobi Circular saw:
https://www.homedepot.com/p/RYOBI-18-...
The angle grinder I used is several years old. But most home centers have a wide selection:
(If possible, make a box that is 6 ft or 8 ft long to avoid needing to use an angle grinder and just buy steel angles already cut at 6 ft or 8 ft.)
https://www.homedepot.com/s/angle%252...
You can also rent tools at Home Depot (Also check your local home center to see if they rent tools out if you dont have a Home Depot near you):
https://www.homedepot.com/c/tool_and_...
I used a 12-inch rafter square (but you can also get smaller ones for cheaper):
https://www.homedepot.com/p/Empire-12...
I used heavier duty clamps but you can use much cheaper clamps for cutting plywood:
(A couple of 12 inch clamps should be fine, and maybe one 24 inch or a 36 inch clamp to hold the larger pieces.)
https://www.homedepot.com/p/BESSEY-12...
https://www.homedepot.com/p/BESSEY-6-...
https://www.homedepot.com/p/DEWALT-24...
https://www.homedepot.com/p/DEWALT-12...
I used this T-Square (though you can use practically anything to guide your circular saw as long as it's straight):
https://www.homedepot.com/p/Empire-48...
You can use this trim square to help you cut 2x4s to length:
https://www.homedepot.com/p/Milwaukee...
Metal countersink drill bit:
https://www.homedepot.com/p/RYOBI-3-4...
2x4 Douglas Fir:
https://www.homedepot.com/p/2-in-x-4-...
23/32 plywood (for the walls of the skate box) :
https://www.homedepot.com/p/23-32-in-...
15/32 plywood (for the top):
https://www.homedepot.com/p/15-32-in-...
Masonite 4x8 sheet (tempered hardboard):
https://www.homedepot.com/p/Hardboard...
Masonite (2x4 sheet):
https://www.homedepot.com/p/Hardboard...
2 in. x 72 in. Angle Plain Steel with 0.125 Thick (Coping for skate box, which was cut to 60 inches with an angle grinder):
https://www.homedepot.com/p/2-in-x-72...
I used 2.5-inch coarse Drywall screws (DONT FORGET TO PREDRILL YOUR HOLES (1/8th inch drill bit should be good.):
https://www.homedepot.com/p/Grip-Rite...
Cheaper, decent furniture dolly:
https://www.homedepot.com/p/Milwaukee...
Better quality furniture dolly:
https://www.uline.com/Product/Detail/...
You could also potentially make your own using scrap 2x4s and buy some 4 inch casters
https://www.homedepot.com/p/Everbilt-...
Comment down below if you have any questions!
Jukin Media Verified
Interested in licensing this footage?
Learn more @ https://www.jukinmedia.com/licensing/...
5 سال پیش
در تاریخ 1398/05/25 منتشر شده
است.
9,422
بـار بازدید شده