Leadshine Hybrid Servo Motor and Driver - Cloudray Laser
16.3 هزار بار بازدید -
4 سال پیش
-
In this video I will
In this video I will introduce the Leadshine Hybrid Servo Closed Loop Stepper Motors and Drivers from Cloudray Laser.
I Used the 3 Phase - Leadshine - Nema 23 Motor - Model 573HBM20-1000
AND
the Leadshine Hybrid Servo Driver Model HBS57
These are available in a set from Cloudray Laser Here - https://www.cloudraylaser.com/collect...
https://s.click.aliexpress.com/e/_d6Q...
Leadshine’s Website - http://www.leadshine.com/
The Hybrid-Servo Stepper motor has this encoder attached to the back of the motor, this encoder is what provides feedback to the driver communicating encoder cable.
Closed loop motors Advantages
-it has a feedback encoder in the motor and allows the motor to communicate with the controller missed steps or reach limit
-they have a lower operating temperature, that is, they run cooler than open loop stepper motors, the hybrid servo drive controls the required amps to the motor by increasing and decreasing as needed, so if the motor is not in motion then amps supplied to the motor are reduced.
-Closed-loop, eliminates loss of synchronization
-Higher torque and higher speed
-Reduced Motor Heating
-Smoother motion and much quieter then regular stepper motors
-No Tuning and always stable
-Quick response, no delay and almost no settle time
-High torque at starting and low speed, high 'stiffness' at standstill
-They Offer "Servo-like" performance at a much lower cost
Hybrid Servo Drive (closed loop driver)
-Takes signal from the motor and processes info to correct motor movements, for example if it moves 4 steps and it was supposed to move 5 then it will move the motor 1 extra step needed.
If the motor is forced more than 90 degree turn on the axis it will trigger an alarm until the issue is corrected.
Options for the Hybrid Servo Drive
-Using the RS232 port (optional cable and software required) you are able to reprogram the drive to suit your more advanced and specific requirements and access diagnostics.
Thanks for Visiting.
Until next time, take care
Cheers Matthew
Visit Matt's Workshop at MW Laser https://www.mwlaser.com.au
Instagram Instagram: mattsworkshop_mwlaser
Facebook Facebook: mattsworkshopau
== If you'd like to support my channel financially so I can continue to produce content you can do via PayPal here-- https://www.paypal.me/mattsworkshop -- Thank You ====
Any questions please feel free to email me [email protected] or leave a comment below.
NOTE: This is not a paid production or advertisement. The featured product was provided by Cloudray to allow me to provide viewers with an installation / how-to video.
I Used the 3 Phase - Leadshine - Nema 23 Motor - Model 573HBM20-1000
AND
the Leadshine Hybrid Servo Driver Model HBS57
These are available in a set from Cloudray Laser Here - https://www.cloudraylaser.com/collect...
https://s.click.aliexpress.com/e/_d6Q...
Leadshine’s Website - http://www.leadshine.com/
The Hybrid-Servo Stepper motor has this encoder attached to the back of the motor, this encoder is what provides feedback to the driver communicating encoder cable.
Closed loop motors Advantages
-it has a feedback encoder in the motor and allows the motor to communicate with the controller missed steps or reach limit
-they have a lower operating temperature, that is, they run cooler than open loop stepper motors, the hybrid servo drive controls the required amps to the motor by increasing and decreasing as needed, so if the motor is not in motion then amps supplied to the motor are reduced.
-Closed-loop, eliminates loss of synchronization
-Higher torque and higher speed
-Reduced Motor Heating
-Smoother motion and much quieter then regular stepper motors
-No Tuning and always stable
-Quick response, no delay and almost no settle time
-High torque at starting and low speed, high 'stiffness' at standstill
-They Offer "Servo-like" performance at a much lower cost
Hybrid Servo Drive (closed loop driver)
-Takes signal from the motor and processes info to correct motor movements, for example if it moves 4 steps and it was supposed to move 5 then it will move the motor 1 extra step needed.
If the motor is forced more than 90 degree turn on the axis it will trigger an alarm until the issue is corrected.
Options for the Hybrid Servo Drive
-Using the RS232 port (optional cable and software required) you are able to reprogram the drive to suit your more advanced and specific requirements and access diagnostics.
Thanks for Visiting.
Until next time, take care
Cheers Matthew
Visit Matt's Workshop at MW Laser https://www.mwlaser.com.au
Instagram Instagram: mattsworkshop_mwlaser
Facebook Facebook: mattsworkshopau
== If you'd like to support my channel financially so I can continue to produce content you can do via PayPal here
Any questions please feel free to email me [email protected] or leave a comment below.
NOTE: This is not a paid production or advertisement. The featured product was provided by Cloudray to allow me to provide viewers with an installation / how-to video.
4 سال پیش
در تاریخ 1399/02/06 منتشر شده
است.
16,321
بـار بازدید شده