K-Swap Ferrari - Fuel Cell, Control Arms, Spindles, Steering Wheels, and More! Ep. 54
57.6 هزار بار بازدید -
3 سال پیش
-
Contribute to Evan Brown's GoFundMe:
Contribute to Evan Brown's GoFundMe:
https://gofund.me/4e6fc5d9
Now THIS is some progress. Not only is the fuel cell mounted, we've got new rear lower control arms, new ball joints, the spinle is mocked up, we've got new rear upper control arm mounts, new tools, a new steering wheel.. MAN! This is a good one.
Tool Links:
Milwaukee M12 Fuel Right-Angle Die Grinder
https://amzn.to/3BCIrNs
Milwaukee M12 Extended Batteries:
https://amzn.to/3kZblBv
Scotch-Brite Roloc Deburr and Finish Wheels
https://amzn.to/3xEKvBf
Roloc Adapter/Arbor
https://amzn.to/3rJyhGs
StanceWorks 2021 Content Sponsors:
H&R Springs
Turtle Wax
RS Future
Nitto Tire
CSF Radiators
Be sure to follow StanceWorks on Instagram: @StanceWorks
Follow me personally on Instagram at @mike_stanceworks
Be sure to support our friends at H&R Springs for helping bring this Honda-swapped Ferrari project to life:
www.hrsprings.com
Last but not least, check out the rest of the gang that helps to make this project happen:
www.turtlewax.com
www.nittotire.com
www.rsfuture.com
www.garrettmotion.com
www.turbosmart.com
Timecodes:
00:00 - Intro
00:18 - What's in This Episode
02:00 - Unboxing the Fuel Cell
02:34 - The Finished Fuel Cell has Arrived!
03:06 - Cutting Tabs off the Chassis
03:59 - Can I Measure?
04:38 - Test Fitting the Fuel Cell
05:13 - Mounting the Fuel Cell: Tabs
06:16 - Mounting the Fuel Cell: Straps
06:58 - Mounting the Fuel Cell: Corner Brackets
07:35 - Mounted!
08:24 - I figured out where I messed up in the last Episode
10:30 - Building the Replacement RLCAs
11:07 - New Lower Ball Joints
11:52 - Completed Lower Control Arms
12:17 - Upper Control Arm Mounts
13:34 - Deburring Roloc Discs - Incredible for Mill Scale!
14:33 - Mocking up a Spindle
15:15 - Nic Builds a Tig Torch Holder
15:41 - Narita Dogfight / Tanida Steering Wheel
16:27 - A Fundraiser for Evan Brown
18:05 - Question 1 - Why Not Use Straight Tubes on the Control Arms
19:54 - Question 2- Why Not Move the Lower Control Arm Mounts?
20:46 - Question 3 - Why Not Ream the Ball Joint Provision on the Spindle?
21:33 - Question 4 - Why Do You Weld Without Gloves? / Outro
https://gofund.me/4e6fc5d9
Now THIS is some progress. Not only is the fuel cell mounted, we've got new rear lower control arms, new ball joints, the spinle is mocked up, we've got new rear upper control arm mounts, new tools, a new steering wheel.. MAN! This is a good one.
Tool Links:
Milwaukee M12 Fuel Right-Angle Die Grinder
https://amzn.to/3BCIrNs
Milwaukee M12 Extended Batteries:
https://amzn.to/3kZblBv
Scotch-Brite Roloc Deburr and Finish Wheels
https://amzn.to/3xEKvBf
Roloc Adapter/Arbor
https://amzn.to/3rJyhGs
StanceWorks 2021 Content Sponsors:
H&R Springs
Turtle Wax
RS Future
Nitto Tire
CSF Radiators
Be sure to follow StanceWorks on Instagram: @StanceWorks
Follow me personally on Instagram at @mike_stanceworks
Be sure to support our friends at H&R Springs for helping bring this Honda-swapped Ferrari project to life:
www.hrsprings.com
Last but not least, check out the rest of the gang that helps to make this project happen:
www.turtlewax.com
www.nittotire.com
www.rsfuture.com
www.garrettmotion.com
www.turbosmart.com
Timecodes:
00:00 - Intro
00:18 - What's in This Episode
02:00 - Unboxing the Fuel Cell
02:34 - The Finished Fuel Cell has Arrived!
03:06 - Cutting Tabs off the Chassis
03:59 - Can I Measure?
04:38 - Test Fitting the Fuel Cell
05:13 - Mounting the Fuel Cell: Tabs
06:16 - Mounting the Fuel Cell: Straps
06:58 - Mounting the Fuel Cell: Corner Brackets
07:35 - Mounted!
08:24 - I figured out where I messed up in the last Episode
10:30 - Building the Replacement RLCAs
11:07 - New Lower Ball Joints
11:52 - Completed Lower Control Arms
12:17 - Upper Control Arm Mounts
13:34 - Deburring Roloc Discs - Incredible for Mill Scale!
14:33 - Mocking up a Spindle
15:15 - Nic Builds a Tig Torch Holder
15:41 - Narita Dogfight / Tanida Steering Wheel
16:27 - A Fundraiser for Evan Brown
18:05 - Question 1 - Why Not Use Straight Tubes on the Control Arms
19:54 - Question 2- Why Not Move the Lower Control Arm Mounts?
20:46 - Question 3 - Why Not Ream the Ball Joint Provision on the Spindle?
21:33 - Question 4 - Why Do You Weld Without Gloves? / Outro
3 سال پیش
در تاریخ 1400/05/19 منتشر شده
است.
57,629
بـار بازدید شده