2 Simple Ways to Make Stronger 3D Prints + an Experimental Way
99.5 هزار بار بازدید -
7 ماه پیش
-
Is the simplest solution always
Is the simplest solution always the best? Or, is the experimental solution the way to go? We're looking at a few ways to make stronger prints in this video.
Help support this channel! Patreon: Needitmakeit
We had a pretty epic but funny fail, I made a set of prints for a friend looking to make his Yaseu FT-891 Radio portable. I found a nicely designed set and printed them for him and then went and sent him a short video showing that they were flexible so we were pretty confident that they'd work well. Well he arrived and we were about to mount them, and he accidently broke one by twisting it, like I had in my video to him. It made me wonder if this was the right solution to use on an expensive radio and if I should modify the design to make it stronger.
I came up with a few different options but thought about using a technique that I had used in woodworking called steam bending, aligning the 'grain' of the plastic to be continuous.
Each of these prints were made from the same spool of filament, extremely dry and printed with no fans. The original model which broke was printed with normal fans and the door was open on the printer. I forgot to mention that part in the video.
Check out the video for all of the details, it was a lot of fun and I learned quite a bit on this one.
I hope you found this video helpful and interesting!
Another way to support this channel indirectly is through my affiliate links (where I receive a small commission). It helps me to continue to provide high-quality content videos. Thank you for your support!
NEW MIC (I bought this)
https://amzn.to/3vcMKAr - Rode Wireless ME mic (Saved me about 4+ hours/vid)
https://amzn.to/3NBFvZe - Mag clip (Super handy, but a little pricy)
BAMBU PRINTERS
https://shrsl.com/4aghz
CREALITY PRINTERS
https://shrsl.com/4aghy
CREALITY HYPER PLA
https://shrsl.com/4aghn
Original Design:
https://www.thingiverse.com/thing:475...
Remix:
https://www.thingiverse.com/thing:639...
#bambu
#crealityk1
#3dprinting
Help support this channel! Patreon: Needitmakeit
We had a pretty epic but funny fail, I made a set of prints for a friend looking to make his Yaseu FT-891 Radio portable. I found a nicely designed set and printed them for him and then went and sent him a short video showing that they were flexible so we were pretty confident that they'd work well. Well he arrived and we were about to mount them, and he accidently broke one by twisting it, like I had in my video to him. It made me wonder if this was the right solution to use on an expensive radio and if I should modify the design to make it stronger.
I came up with a few different options but thought about using a technique that I had used in woodworking called steam bending, aligning the 'grain' of the plastic to be continuous.
Each of these prints were made from the same spool of filament, extremely dry and printed with no fans. The original model which broke was printed with normal fans and the door was open on the printer. I forgot to mention that part in the video.
Check out the video for all of the details, it was a lot of fun and I learned quite a bit on this one.
I hope you found this video helpful and interesting!
Another way to support this channel indirectly is through my affiliate links (where I receive a small commission). It helps me to continue to provide high-quality content videos. Thank you for your support!
NEW MIC (I bought this)
https://amzn.to/3vcMKAr - Rode Wireless ME mic (Saved me about 4+ hours/vid)
https://amzn.to/3NBFvZe - Mag clip (Super handy, but a little pricy)
BAMBU PRINTERS
https://shrsl.com/4aghz
CREALITY PRINTERS
https://shrsl.com/4aghy
CREALITY HYPER PLA
https://shrsl.com/4aghn
Original Design:
https://www.thingiverse.com/thing:475...
Remix:
https://www.thingiverse.com/thing:639...
#bambu
#crealityk1
#3dprinting
7 ماه پیش
در تاریخ 1402/10/02 منتشر شده
است.
99,546
بـار بازدید شده