1940's Delta Jointer restore: re-surfacing planes
3.9 هزار بار بازدید -
4 ماه پیش
-
This video is the first
This video is the first of four. It's (mostly) about flattening infeed and outfeed tables. The jointer is some variation of a 6" Delta Milwaukee, model 37-207. This is a very common machine to find on the second-hand market. This video series was designed to include all the information that I would have liked to know before restoring one.
(1) Re-surfacing planes:
►1940's Delta Jointer restore: re-surf...
(2) Installing new bearings:
►1940's Delta Jointer: Bearing Replace...
(3) Assembling the jointer:
►1940's Delta Jointer re-assembly (res...
(4) Assembling fence, simple sharpening, and installing knives:
►1940's Delta Jointer: Fence assembly,...
~~~~~
●Replacement Bearings (without extended race):
1) Front side (smaller one):
15mm/35mm/13mm (Inside diameter/Outside diameter/Width).
Search using the following title. “PGN (2 Pack) 6202-2RS Bearing Lubricated Chrome
Steel Sealed Ball Bearings 15x35x11mm with Rubber Seal & High RPM Support ”
2) Back/pulley side (bigger one):
17mm/40mm/13mm (Inside diameter/Outside diameter/Width).
Search using the following title. “PGN (2 Pack) 6203-2RS Bearing Lubricated Chrome
Steel Sealed Ball Bearings 17x40x12mm with Rubber Seal & High RPM Support”
●Replacement Knives:
POWERTEC 6 Inch Jointer Blades for Delta 37-190 37-195 37-205 37-220 37-275X Jointer, Replacement for 37-658 Jointer Knives, Set of 3 (148032)
●Replacement Set-screws:
These are found throughout the machine. Check local hardware store first. They have a ¼-28 thread pattern; that means the threads were cut from ¼" rod, and they're spaced at 28 threads per inch.
●Diamond Sharpening Plates:
I will not provide free advertisements here, but simply search for "Diamond 5 Pcs Knife Sharpening Stone," and try not to spend more than 15 bucks. If you're shopping on the 'big A,' save the item to your watch list (without buying it), and then watch as the price magically drops over the next day or two. This is called 'dynamic pricing,' also known as scalping. You're welcome. I'm one of the good guys, I swear. You should also be thanking me for not putting mid-roll ads in this video, but who's counting?
●DELTA MILWAUKEE operating and maintenance instructions
(applies to models 34-205 34-207 37-205 37-207 and many variants):
http://vintagemachinery.org/pubs/1141...
Funny clip taken from "What Does It Really Take..." by "Tools In Action"
That's an attribution, not a channel recommendation.
(1) Re-surfacing planes:
►1940's Delta Jointer restore: re-surf...
(2) Installing new bearings:
►1940's Delta Jointer: Bearing Replace...
(3) Assembling the jointer:
►1940's Delta Jointer re-assembly (res...
(4) Assembling fence, simple sharpening, and installing knives:
►1940's Delta Jointer: Fence assembly,...
~~~~~
●Replacement Bearings (without extended race):
1) Front side (smaller one):
15mm/35mm/13mm (Inside diameter/Outside diameter/Width).
Search using the following title. “PGN (2 Pack) 6202-2RS Bearing Lubricated Chrome
Steel Sealed Ball Bearings 15x35x11mm with Rubber Seal & High RPM Support ”
2) Back/pulley side (bigger one):
17mm/40mm/13mm (Inside diameter/Outside diameter/Width).
Search using the following title. “PGN (2 Pack) 6203-2RS Bearing Lubricated Chrome
Steel Sealed Ball Bearings 17x40x12mm with Rubber Seal & High RPM Support”
●Replacement Knives:
POWERTEC 6 Inch Jointer Blades for Delta 37-190 37-195 37-205 37-220 37-275X Jointer, Replacement for 37-658 Jointer Knives, Set of 3 (148032)
●Replacement Set-screws:
These are found throughout the machine. Check local hardware store first. They have a ¼-28 thread pattern; that means the threads were cut from ¼" rod, and they're spaced at 28 threads per inch.
●Diamond Sharpening Plates:
I will not provide free advertisements here, but simply search for "Diamond 5 Pcs Knife Sharpening Stone," and try not to spend more than 15 bucks. If you're shopping on the 'big A,' save the item to your watch list (without buying it), and then watch as the price magically drops over the next day or two. This is called 'dynamic pricing,' also known as scalping. You're welcome. I'm one of the good guys, I swear. You should also be thanking me for not putting mid-roll ads in this video, but who's counting?
●DELTA MILWAUKEE operating and maintenance instructions
(applies to models 34-205 34-207 37-205 37-207 and many variants):
http://vintagemachinery.org/pubs/1141...
Funny clip taken from "What Does It Really Take..." by "Tools In Action"
That's an attribution, not a channel recommendation.
4 ماه پیش
در تاریخ 1403/01/30 منتشر شده
است.
3,905
بـار بازدید شده