Easy Evil Dead Chainsaw Hand PROP Ash Williams Cosplay - DIY Tutorial
5 هزار بار بازدید -
2 سال پیش
-
Welcome to my yearly cosplay
Welcome to my yearly cosplay video. Hope I didn't traumatize you with my dumb intros/outros. There is only one Bruce Campbell, and my impression doesn't do him nearly enough justice. Forgive me, o internet.
These cosplay tutorials are some of the most challenging to make and take the most resources, effort, and time, so your support means the world to me.
Materials used to create this Prop (I was able to get everything around $50, not including paint/glue/various hardware, buy specialty hardware, like the large hex nut and bolt, by the single piece at stores to save more money):
- Main Body: Arizona Tea Gallon:
From any store, get one with removable labels
- Exhaust Vent Outer Edge: Kohler Tank Gasket
https://www.homedepot.com/p/KOHLER-Ta...
- Exhaust Vent Inner Grate: 4 inch Round Drainage Grate
https://www.homedepot.com/p/NDS-4-in-...
- Outer Handle Connector: 1/2 in. Schedule 40 and 80 PVC Type-LL Conduit Body
https://www.homedepot.com/p/Carlon-1-...
- Outer Handle: 1/2 in. 90° Schedule 40 PVC Belled End Standard Radius Elbow
https://www.homedepot.com/p/Carlon-1-...
- Outer Handle End Cap: 3/4 in. PVC Schedule 40 Socket Cap
https://www.homedepot.com/p/Charlotte...
- Sleeve Connector Flange: 4 in. No Hub Coupling
https://www.homedepot.com/p/ECO-FLO-4...
- Sleeve to Body Connectors: 2 in. Zinc-Plated Mending Plate
https://www.homedepot.com/p/Everbilt-...
- On/Off Switch: 8 Amp Single-Pole Toggle Switch
https://www.homedepot.com/p/Gardner-B...
- Blade: 1/2 in. x 5-1/2 in. x 96 in. Primed MDF Baseboard (by the foot)
https://www.homedepot.com/p/Alexandri...
(You can get a much smaller, cheaper baseboard to make a more realistic looking blade that isn't so cartoony. Make sure to get thick enough board to support connecting your chain with small screws.)
- Chain: #14 x 1 ft. Zinc Plated Steel Jack Chain (by the foot)
https://www.homedepot.com/p/Everbilt-...
- Large Flat Washer and Hex Bolt and Nut:
https://www.homedepot.com/p/Everbilt-...
https://www.lowes.com/pd/Hillman-5-8-...
https://www.lowes.com/pd/Hillman-5-8-...
- Inner Handle and Pull Cord Handle: 3/4 in. Wood Dowel
https://www.homedepot.com/p/6412U-3-4...
- Fake Pullcord: Shoestring or Small Rope.
- The extra aesthetic pieces (dryer outlet plate, striker plate, etc.) are at your own discretion.
Hope that helps! Happy building! Let me know how your build goes in the comments!
Check out: Patreon: JetFalco if you'd like to support my videos, comics, and art.
https://www.dreamersecho.com/links
Comics, Art, Music, Audiobooks, Podcasts, Videos, and MORE...
#cosplay #diycostume #chainsaw
These cosplay tutorials are some of the most challenging to make and take the most resources, effort, and time, so your support means the world to me.
Materials used to create this Prop (I was able to get everything around $50, not including paint/glue/various hardware, buy specialty hardware, like the large hex nut and bolt, by the single piece at stores to save more money):
- Main Body: Arizona Tea Gallon:
From any store, get one with removable labels
- Exhaust Vent Outer Edge: Kohler Tank Gasket
https://www.homedepot.com/p/KOHLER-Ta...
- Exhaust Vent Inner Grate: 4 inch Round Drainage Grate
https://www.homedepot.com/p/NDS-4-in-...
- Outer Handle Connector: 1/2 in. Schedule 40 and 80 PVC Type-LL Conduit Body
https://www.homedepot.com/p/Carlon-1-...
- Outer Handle: 1/2 in. 90° Schedule 40 PVC Belled End Standard Radius Elbow
https://www.homedepot.com/p/Carlon-1-...
- Outer Handle End Cap: 3/4 in. PVC Schedule 40 Socket Cap
https://www.homedepot.com/p/Charlotte...
- Sleeve Connector Flange: 4 in. No Hub Coupling
https://www.homedepot.com/p/ECO-FLO-4...
- Sleeve to Body Connectors: 2 in. Zinc-Plated Mending Plate
https://www.homedepot.com/p/Everbilt-...
- On/Off Switch: 8 Amp Single-Pole Toggle Switch
https://www.homedepot.com/p/Gardner-B...
- Blade: 1/2 in. x 5-1/2 in. x 96 in. Primed MDF Baseboard (by the foot)
https://www.homedepot.com/p/Alexandri...
(You can get a much smaller, cheaper baseboard to make a more realistic looking blade that isn't so cartoony. Make sure to get thick enough board to support connecting your chain with small screws.)
- Chain: #14 x 1 ft. Zinc Plated Steel Jack Chain (by the foot)
https://www.homedepot.com/p/Everbilt-...
- Large Flat Washer and Hex Bolt and Nut:
https://www.homedepot.com/p/Everbilt-...
https://www.lowes.com/pd/Hillman-5-8-...
https://www.lowes.com/pd/Hillman-5-8-...
- Inner Handle and Pull Cord Handle: 3/4 in. Wood Dowel
https://www.homedepot.com/p/6412U-3-4...
- Fake Pullcord: Shoestring or Small Rope.
- The extra aesthetic pieces (dryer outlet plate, striker plate, etc.) are at your own discretion.
Hope that helps! Happy building! Let me know how your build goes in the comments!
Check out: Patreon: JetFalco if you'd like to support my videos, comics, and art.
https://www.dreamersecho.com/links
Comics, Art, Music, Audiobooks, Podcasts, Videos, and MORE...
#cosplay #diycostume #chainsaw
2 سال پیش
در تاریخ 1401/11/07 منتشر شده
است.
5,075
بـار بازدید شده