DIY Lighted RV Flag Pole - full time rving - RVSWAT
63.8 هزار بار بازدید -
6 سال پیش
-
In this video we show
In this video we show you how we built our lighted flag pole.
Also check out this video for the updates I added to the pole. Update-Upgrade DIY Lighted RV Flag Po... All parts where purchased at Lowes.
Parts Needed:
1 - 10' piece of 1" PVC pipe
1 - 1" PVC 45 degree coupler
1 - 1" PVC T coupler
2 - 1" PVC caps
1 - 4' piece of pre-cut rebar 1/2' thick
1 - Package of 1/2" X 2" fender washers
1 - Package of 1" cup hooks
1 - Solar flag pole light
Assembly Instructions:
1 - Cut 10' PVC pipe into two 4 foot sections and two 1 foot sections.
2 - Align cup hooks on one of the 4 foot PVC sections with flag grommets on flag and pre-drill small holes to screw in cup hooks easier.
3 - Place one of the fender washers onto one end of the rebar and bang rebard into the ground with the washer side down about 1 foot.
4 - Slide one of the 4 foot PVC pipes over the rebar. PVC pipe should be able to rotate freely on the washer.
5 - Place 45 degree PVC coupler onto the top of the 4 foot section that is over the rebar.
6 - Insert one of the 1 foot PVC pipes into the 45 degree coupler and place the T coupler onto the open end of the same 1 foot PVC pipe.
7 - Place the other 1 foot PVC section onto the T with it facing towards the ground and install one of the PVC caps.
8 - Place the other 4 foot PVC section with the cup hooks into the other end of the T and place the other PVC cap at the top of the 4 foot PVC pipe.
9 - Place flag gourmets onto cup hooks, and pinch cup hooks closed with pliers to prevent the flag from coming off.
10 - Install flag pole solar light.
Also check out this video for the updates I added to the pole. Update-Upgrade DIY Lighted RV Flag Po... All parts where purchased at Lowes.
Parts Needed:
1 - 10' piece of 1" PVC pipe
1 - 1" PVC 45 degree coupler
1 - 1" PVC T coupler
2 - 1" PVC caps
1 - 4' piece of pre-cut rebar 1/2' thick
1 - Package of 1/2" X 2" fender washers
1 - Package of 1" cup hooks
1 - Solar flag pole light
Assembly Instructions:
1 - Cut 10' PVC pipe into two 4 foot sections and two 1 foot sections.
2 - Align cup hooks on one of the 4 foot PVC sections with flag grommets on flag and pre-drill small holes to screw in cup hooks easier.
3 - Place one of the fender washers onto one end of the rebar and bang rebard into the ground with the washer side down about 1 foot.
4 - Slide one of the 4 foot PVC pipes over the rebar. PVC pipe should be able to rotate freely on the washer.
5 - Place 45 degree PVC coupler onto the top of the 4 foot section that is over the rebar.
6 - Insert one of the 1 foot PVC pipes into the 45 degree coupler and place the T coupler onto the open end of the same 1 foot PVC pipe.
7 - Place the other 1 foot PVC section onto the T with it facing towards the ground and install one of the PVC caps.
8 - Place the other 4 foot PVC section with the cup hooks into the other end of the T and place the other PVC cap at the top of the 4 foot PVC pipe.
9 - Place flag gourmets onto cup hooks, and pinch cup hooks closed with pliers to prevent the flag from coming off.
10 - Install flag pole solar light.
6 سال پیش
در تاریخ 1397/04/29 منتشر شده
است.
63,824
بـار بازدید شده