Pressure Reducing Valve Replacement Step-By-Step Guide
17 هزار بار بازدید -
2 سال پیش
-
The great thing about pressure
The great thing about pressure reducing valves is that they're set to regulate your water flow to a specific pressure. That means if there's a sudden spike in your area's municipal water pressure, the spring and diaphragm in the valve will tighten and you'll still have a consistent amount of pressure in your home. PRVs are effectively multi-functional - by lowering outlet pressure and flow rate, they also help reduce excessive water consumption and plumbing noise. Many valves have a nut, screw, or knob attached to them that allow you to do the actual adjusting. Turning the screw or knob clockwise typically increases the water pressure while turning it counter-clockwise lowers the pressure. We do not recommend adjusting your pressure reducing valve if it is over a year old.
Normal psi for a home pipe system is between 30 and 80 psi. While you don't want the psi to be too low, it violates code to be above 80. Instead, you should aim for a psi that's between 60 and 70.For most houses, 80 psi (pounds per square inch) is about right. If the water pressure is over 100 psi, that's too much. High water pressure puts a lot of unnecessary strain on your home's plumbing system. This often leads to loosened joints, pinhole leaks in the pipes, dripping faucets, shower heads, running toilets, burst wash machine hoses or icemaker lines. Left unrepaired, leaking pipes are likely to cause mold growth and other serious water damage to your home. @TappPlumbing
Watts Small Body PRV Double Union:
https://amzn.to/3fzNU1x
Watts 25 AUB:
https://amzn.to/3sZI1xt
Long Body Wilkins/Zurn:
https://amzn.to/3fAwfqj
Zurn Repair Kit:
https://amzn.to/3sZRdSz
00:00 Introduction
00:20 Sawing off PRV
00:49 Pressure Reducing Valve hidden under water heater
01:23 Taking apart the PRV
01:51 Using a rebuild kit for your Pressure Reducing Valve
02:52 Rebuild kits usually do not work for pressure reducing valves
03:40 Cutting the Hole for Removal
04:27 Keep male threads in tact to add new PRV
05:13 Going from Single union to double union Pressure Reducing Valve
05:42 how to install new PRV
06:01 Make sure arrow goes with the direction of flow of water
06:19 Make sure gaskets are installed on bothe sides of PRV
07:01 Watts Pressure Reducing Valves make noises throughout the whole house
07:18 Union NUTS are brand specific
Normal psi for a home pipe system is between 30 and 80 psi. While you don't want the psi to be too low, it violates code to be above 80. Instead, you should aim for a psi that's between 60 and 70.For most houses, 80 psi (pounds per square inch) is about right. If the water pressure is over 100 psi, that's too much. High water pressure puts a lot of unnecessary strain on your home's plumbing system. This often leads to loosened joints, pinhole leaks in the pipes, dripping faucets, shower heads, running toilets, burst wash machine hoses or icemaker lines. Left unrepaired, leaking pipes are likely to cause mold growth and other serious water damage to your home. @TappPlumbing
Watts Small Body PRV Double Union:
https://amzn.to/3fzNU1x
Watts 25 AUB:
https://amzn.to/3sZI1xt
Long Body Wilkins/Zurn:
https://amzn.to/3fAwfqj
Zurn Repair Kit:
https://amzn.to/3sZRdSz
00:00 Introduction
00:20 Sawing off PRV
00:49 Pressure Reducing Valve hidden under water heater
01:23 Taking apart the PRV
01:51 Using a rebuild kit for your Pressure Reducing Valve
02:52 Rebuild kits usually do not work for pressure reducing valves
03:40 Cutting the Hole for Removal
04:27 Keep male threads in tact to add new PRV
05:13 Going from Single union to double union Pressure Reducing Valve
05:42 how to install new PRV
06:01 Make sure arrow goes with the direction of flow of water
06:19 Make sure gaskets are installed on bothe sides of PRV
07:01 Watts Pressure Reducing Valves make noises throughout the whole house
07:18 Union NUTS are brand specific
2 سال پیش
در تاریخ 1401/09/10 منتشر شده
است.
17,048
بـار بازدید شده