How to Build a Belt Conveyor
207.6 هزار بار بازدید -
6 سال پیش
-
Step by step guide on
Step by step guide on how to build a aluminium conveyor from a conveyor kit.
We can provide all or some of the parts you need.
Call 01525 850316 for more information.
DIY Conveyor instructions
1. Cut the aluminium profile to size we can do this for you.
2. Lay out the parts and assemble angle brackets ...We can supply angle brackets.
3. Assemble the aluminium profile belt base using the angle brackets and profile.
4. Measure the spacing of brackets and make sure they are square then tighten with an allen key.
5. Balance on table or pre made legs and slide on the idler and drive end drums... square up and secure using the fittings provided. If you would like to build the idler and drive drum from scratch you can see our other video's in this series.
6. Place and secure using double sided tape the metal sheet used for the belt bed.
7. Build the aluminium legs using fittings measure and square up then tighten.
8. Screw in the feet.
9. Add the leg bracket which enable you to angle the conveyor if required.
10. Put end caps on the profile legs
11. Place the top bed with the drums on the legs then carefully slide on the belt.
12. Then secure using the brackets.
13. Place the motor on the drive drum end and secure.
14. If you require a start stop with variable speed you will need to mount the inverter.
15. Wire up the Inverter and motor.
16. Place ends on the idler drum and fix.
16. Then simply plug in and switch on.
THIS IS A VERY BASIC GUIDE .....
If you would like a more detailed description then please visit our website
http://www.kit-conveyors.co.uk/how-to...
This is only part of a series of video's to help you build a DIY Conveyor by using our Kit of Parts
Enabling you to build cheap conveyors at a low cost.
#conveyors #conveyorkit #cheapconveyors
We can provide all or some of the parts you need.
Call 01525 850316 for more information.
DIY Conveyor instructions
1. Cut the aluminium profile to size we can do this for you.
2. Lay out the parts and assemble angle brackets ...We can supply angle brackets.
3. Assemble the aluminium profile belt base using the angle brackets and profile.
4. Measure the spacing of brackets and make sure they are square then tighten with an allen key.
5. Balance on table or pre made legs and slide on the idler and drive end drums... square up and secure using the fittings provided. If you would like to build the idler and drive drum from scratch you can see our other video's in this series.
6. Place and secure using double sided tape the metal sheet used for the belt bed.
7. Build the aluminium legs using fittings measure and square up then tighten.
8. Screw in the feet.
9. Add the leg bracket which enable you to angle the conveyor if required.
10. Put end caps on the profile legs
11. Place the top bed with the drums on the legs then carefully slide on the belt.
12. Then secure using the brackets.
13. Place the motor on the drive drum end and secure.
14. If you require a start stop with variable speed you will need to mount the inverter.
15. Wire up the Inverter and motor.
16. Place ends on the idler drum and fix.
16. Then simply plug in and switch on.
THIS IS A VERY BASIC GUIDE .....
If you would like a more detailed description then please visit our website
http://www.kit-conveyors.co.uk/how-to...
This is only part of a series of video's to help you build a DIY Conveyor by using our Kit of Parts
Enabling you to build cheap conveyors at a low cost.
#conveyors #conveyorkit #cheapconveyors
6 سال پیش
در تاریخ 1397/04/26 منتشر شده
است.
207,604
بـار بازدید شده