LoRa/LoRaWAN tutorial 10: RSSI and SNR
53.5 هزار بار بازدید -
6 سال پیش
-
If you like this video
If you like this video and want to support me, go this page for my donation Paypal or crypto addresses:
mobilefish
This is part 10 of the LoRa/LoRaWAN tutorial.
In this video series different topics will be explained which will help you to understand LoRa/LoRaWAN.
It is recommended to watch each video sequentially as I may refer to certain LoRa/LoRaWAN topics explained earlier.
In this video I will explain what RSSI and SNR are.
The Received Signal Strength Indication (RSSI) is the received signal power in milliwatts and is measured in dBm.
This value can be used as a measurement of how well a receiver can "hear" a signal from a sender.
The RSSI is measured in dBm and is a negative value.
The closer to 0 the better the signal is.
Typical LoRa RSSI values are:
RSSI minimum = -120 dBm.
If RSSI=-30dBm: signal is strong.
If RSSI=-120dBm: signal is weak.
Signal-to-Noise Ratio (SNR) is the ratio between the received power signal and the noise floor power level.
The noise floor is an area of all unwanted interfering signal sources which can corrupt the transmitted signal and therefore re-transmissions will occur.
If SNR is greater than 0, the received signal operates above the noise floor.
If SNR is smaller than 0, the received signal operates below the noise floor.
Normally the noise floor is the physical limit of sensitivity, however LoRa works below the noise level.
Typical LoRa SNR values are between: -20dB and +10dB
A value closer to +10dB means the received signal is less corrupted.
LoRa can demodulate signals which are -7.5 dB to -20 dB below the noise floor.
Check out all my other LoRa/LoRaWAN tutorial videos:
LoRa/LoRaWAN tutorials
Subscribe to my YouTube channel:
@mobilefish
The presentation used in this video tutorial can be found at:
https://www.mobilefish.com/developer/...
#mobilefish #lora #lorawan
mobilefish
This is part 10 of the LoRa/LoRaWAN tutorial.
In this video series different topics will be explained which will help you to understand LoRa/LoRaWAN.
It is recommended to watch each video sequentially as I may refer to certain LoRa/LoRaWAN topics explained earlier.
In this video I will explain what RSSI and SNR are.
The Received Signal Strength Indication (RSSI) is the received signal power in milliwatts and is measured in dBm.
This value can be used as a measurement of how well a receiver can "hear" a signal from a sender.
The RSSI is measured in dBm and is a negative value.
The closer to 0 the better the signal is.
Typical LoRa RSSI values are:
RSSI minimum = -120 dBm.
If RSSI=-30dBm: signal is strong.
If RSSI=-120dBm: signal is weak.
Signal-to-Noise Ratio (SNR) is the ratio between the received power signal and the noise floor power level.
The noise floor is an area of all unwanted interfering signal sources which can corrupt the transmitted signal and therefore re-transmissions will occur.
If SNR is greater than 0, the received signal operates above the noise floor.
If SNR is smaller than 0, the received signal operates below the noise floor.
Normally the noise floor is the physical limit of sensitivity, however LoRa works below the noise level.
Typical LoRa SNR values are between: -20dB and +10dB
A value closer to +10dB means the received signal is less corrupted.
LoRa can demodulate signals which are -7.5 dB to -20 dB below the noise floor.
Check out all my other LoRa/LoRaWAN tutorial videos:
LoRa/LoRaWAN tutorials
Subscribe to my YouTube channel:
@mobilefish
The presentation used in this video tutorial can be found at:
https://www.mobilefish.com/developer/...
#mobilefish #lora #lorawan
6 سال پیش
در تاریخ 1397/07/06 منتشر شده
است.
53,549
بـار بازدید شده