How To Remove & Install Mercury Out Drive / bell housing ( Replace Bellows )
26.2 هزار بار بازدید -
3 ماه پیش
-
Removing and Installation MerCruiser ,
Removing and Installation MerCruiser ,
Customer had shift cable Bellow Crack so would take on water in the boat. so removal and install of new bellows and seals.
Order of process, Tool List, and Applicators list, All listed below ⬇️
Oder of operations
- remove prop
- push throttle all the way forward-
- unbolt 6 nuts from stern drive
- unpl
- remove and install throttle cable
- bell housing
- trim sensor
- gear lube oil
Tool List:
● 9/16" Spark plug socket OR Specialty Tool
● 1/2" Hex Socket OR Hinge Pin Tool
● 1/4" drive Rachet
● 3/8" dr Rachet
● 3/8" dr extension
● 1/4" dr extension
● 7mm socket deep and shallow
● Couple diff size - Flathead screwdrivers
● Phillip screwdriver 🪛
● Mallet
● Needle Nose Pliers
● Reg Pliers
● 5/8" Socket
● 13/16" Socket
● 7mm Socket Deep & Shallow
● Zip ties 50lb or whatever you'd like to use
● Bellow Tool helps abit
● Adjustable ( crescent ) wrenc
● Knife
Applicators:
● 2-4-C Marine Grease w/PTFE
● 270 Loctite
● Bellows adhesive # 92-86166Q 1
● "Perfect seal" Permatex Form a gasket
#Howto #boat #mercury #sterndrive #alpha #bellows #motor #MerCruiser # Alpha one gen 1 gen 1 bravo #alpha #bravo #gen1 #genone #alphaone #gen2 #gentwo #bayl #Bayliner #SeaRay #suntracker #lakeday #lake #outboard #inboard #boatmotor #jetboat #jetski #jetskis
Customer had shift cable Bellow Crack so would take on water in the boat. so removal and install of new bellows and seals.
Order of process, Tool List, and Applicators list, All listed below ⬇️
Oder of operations
- remove prop
- push throttle all the way forward-
- unbolt 6 nuts from stern drive
- unpl
- remove and install throttle cable
- bell housing
- trim sensor
- gear lube oil
Tool List:
● 9/16" Spark plug socket OR Specialty Tool
● 1/2" Hex Socket OR Hinge Pin Tool
● 1/4" drive Rachet
● 3/8" dr Rachet
● 3/8" dr extension
● 1/4" dr extension
● 7mm socket deep and shallow
● Couple diff size - Flathead screwdrivers
● Phillip screwdriver 🪛
● Mallet
● Needle Nose Pliers
● Reg Pliers
● 5/8" Socket
● 13/16" Socket
● 7mm Socket Deep & Shallow
● Zip ties 50lb or whatever you'd like to use
● Bellow Tool helps abit
● Adjustable ( crescent ) wrenc
● Knife
Applicators:
● 2-4-C Marine Grease w/PTFE
● 270 Loctite
● Bellows adhesive # 92-86166Q 1
● "Perfect seal" Permatex Form a gasket
#Howto #boat #mercury #sterndrive #alpha #bellows #motor #MerCruiser # Alpha one gen 1 gen 1 bravo #alpha #bravo #gen1 #genone #alphaone #gen2 #gentwo #bayl #Bayliner #SeaRay #suntracker #lakeday #lake #outboard #inboard #boatmotor #jetboat #jetski #jetskis
3 ماه پیش
در تاریخ 1403/02/07 منتشر شده
است.
26,282
بـار بازدید شده