✅ ESP8266 Adiós Comandos AT.
244.1 هزار بار بازدید -
9 سال پیش
-
💣 DISCOUNT 90% FOR OUR
💣 DISCOUNT 90% FOR OUR SUBSCRIBERS❗
MASTER COURSE IN ARDUINO FROM ZERO TO LEVEL👨🎓👩🎓
https://somosioticos.com/master_ardui...
MASTER COURSE IN VESTA 👨🎓👩🎓
https://somosioticos.com/master_vesta...
DO NOT STOP STUDYING NEVER❗
It's over boring! The good is coming!
In this tutorial video, we explain in detail how to free ourselves from the rudimentary AT commands, creating our own firmwares under environment.
YES! Did you understand well! you can make an IoT device without the need for an arduino board! Only with an Esp8266!
IMPORTANT: REMEMBER THAT WHAT WE DO UPLOAD AN UP-TO-DATE FIRMWARE OF COMMANDS IS FOR ALL TO PARTICIPATE ON THE SAME BASIS. YOU CAN TRY TO USE THE ARDUINO IDE DIRECTLY TO FLASH THE ESP, BY PASSING THE FIRMWARE UPDATE STEP, PLEASE NOTE THAT WHEN YOU LOAD YOUR FIRST PROGRAM WITH THE ARDUINO IDE, WHETHER YOU DO IT ABOUT THE ORIGINAL AT FIRMWARE, OR THE UP-TO-DATE FIRMWARE , THIS FIRMWARE WILL BE REPLACED (DELETED FROM THE ESP) BY THE NEW ONE YOU HAVE CREATED WITH ARDUINO AND THE PLATE WILL NO LONGER RESPOND TO THE AT COMMANDS.
IS THIS REVERSIBLE? CLEAR! IF YOU WANT TO RETURN TO THE COMMANDS AT, YOU WILL LOAD THE CORRESPONDING FIRM WITH THE FLASHER AND READY!
Link for file downloads and others:
http://ioting.org/ (then on the menu go to "downloads")
Link ESP8266 Arduino IDE:
https://github.com/esp8266/Arduino
Command to change speed:
AT + CIOBAUD = 115200 (change to 115200)
AT + CIOBAUD = 9600 (change to 9600)
Test code:
int a = 0;
void setup () {
// put your setup code here, to run once:
Serial.begin (115200);
}
void loop () {
// put your main code here, to run repeatedly:
Serial.println ("I AM ESP8266 HERE I AM !!!");
Serial.println (a);
a = a + 1;
delay (500);
}
MASTER COURSE IN ARDUINO FROM ZERO TO LEVEL👨🎓👩🎓
https://somosioticos.com/master_ardui...
MASTER COURSE IN VESTA 👨🎓👩🎓
https://somosioticos.com/master_vesta...
DO NOT STOP STUDYING NEVER❗
It's over boring! The good is coming!
In this tutorial video, we explain in detail how to free ourselves from the rudimentary AT commands, creating our own firmwares under environment.
YES! Did you understand well! you can make an IoT device without the need for an arduino board! Only with an Esp8266!
IMPORTANT: REMEMBER THAT WHAT WE DO UPLOAD AN UP-TO-DATE FIRMWARE OF COMMANDS IS FOR ALL TO PARTICIPATE ON THE SAME BASIS. YOU CAN TRY TO USE THE ARDUINO IDE DIRECTLY TO FLASH THE ESP, BY PASSING THE FIRMWARE UPDATE STEP, PLEASE NOTE THAT WHEN YOU LOAD YOUR FIRST PROGRAM WITH THE ARDUINO IDE, WHETHER YOU DO IT ABOUT THE ORIGINAL AT FIRMWARE, OR THE UP-TO-DATE FIRMWARE , THIS FIRMWARE WILL BE REPLACED (DELETED FROM THE ESP) BY THE NEW ONE YOU HAVE CREATED WITH ARDUINO AND THE PLATE WILL NO LONGER RESPOND TO THE AT COMMANDS.
IS THIS REVERSIBLE? CLEAR! IF YOU WANT TO RETURN TO THE COMMANDS AT, YOU WILL LOAD THE CORRESPONDING FIRM WITH THE FLASHER AND READY!
Link for file downloads and others:
http://ioting.org/ (then on the menu go to "downloads")
Link ESP8266 Arduino IDE:
https://github.com/esp8266/Arduino
Command to change speed:
AT + CIOBAUD = 115200 (change to 115200)
AT + CIOBAUD = 9600 (change to 9600)
Test code:
int a = 0;
void setup () {
// put your setup code here, to run once:
Serial.begin (115200);
}
void loop () {
// put your main code here, to run repeatedly:
Serial.println ("I AM ESP8266 HERE I AM !!!");
Serial.println (a);
a = a + 1;
delay (500);
}
9 سال پیش
در تاریخ 1394/04/30 منتشر شده
است.
244,125
بـار بازدید شده