Toyota key transponder coding | How to program Toyota Hilux key
4.8 هزار بار بازدید -
7 ماه پیش
-
How to code / program
How to code / program a Toyota key from the mid 2000's similar for most models, the Hilux, Hiace, Yaris, Camry etc.
A revision of my first video.
How to code a new key transponder to a Toyota Hilux and set up remote central locking.
Written instructions below if I was a tad fast in the video, these 2 procedures need to be done smoothly
Keys can be found on eBay or from other local manufacturers
Coding the additional key:
1. Start with doors closed and no key is inserted in the ignition key barrel.
2. Put the already registered master key into the ignition barrel.
3. Remove and insert the master key 4 times (ensure the key is registering, as some barrels/ keys are worn, a bit of pressure on the key when inserted should do.)
4. Open and Close the driver's door 6 times, ensure this is done quite quickly (less then 45 seconds)
5. Remove the master key.
6. Insert the new key to be registered into the ignition key barrel within 10 sec.
7. Leave new key in ignition After 60 sec, the new key is registered.
To code the Lock and un-lock:
Start with the key out of the ignition. Open the driver door
1. Perform these steps within 10 seconds:
-Insert the key into the ignition
- Pull key out
- Insert the key into the ignition
- Pull key out
2. Perform these steps within 45 seconds
- Close, then open the drivers door.
- Close, then open the drivers door.
3. Insert the key into the ignition and pull it out.
- Perform these steps within 40 seconds
- Close, then open the drivers door.
- Close, then open the drivers door.
- Insert the key into the ignition and leave in the ignition.
- Close the drivers door
- Turn the ignition to ON (not start), then back to off once (this enters add mode)
- Remove the key from the ignition.
5. The power door locks should lock then unlock automatically indicating successful entry into programming mode.
Return to step 1 if the locks did not cycle
6. Perform these steps within 40 seconds
-Press the lock and unlock buttons on the transmitter simultaneously for 1.5 seconds
-Immediately after letting go of the lock and unlock buttons, press the lock button by itself and hold for 2 seconds. (this needs to be done quite fast)
-The door locks should lock then unlock once indicating successful
programming. If the door locks cycle twice, repeat steps 6 as the remote was not accepted.
7. Open drivers door
Thanks for watching
Intro 00:00
Programming ignition 01:06
Programming door locks 02:25
Conclusion 02:58
A revision of my first video.
How to code a new key transponder to a Toyota Hilux and set up remote central locking.
Written instructions below if I was a tad fast in the video, these 2 procedures need to be done smoothly
Keys can be found on eBay or from other local manufacturers
Coding the additional key:
1. Start with doors closed and no key is inserted in the ignition key barrel.
2. Put the already registered master key into the ignition barrel.
3. Remove and insert the master key 4 times (ensure the key is registering, as some barrels/ keys are worn, a bit of pressure on the key when inserted should do.)
4. Open and Close the driver's door 6 times, ensure this is done quite quickly (less then 45 seconds)
5. Remove the master key.
6. Insert the new key to be registered into the ignition key barrel within 10 sec.
7. Leave new key in ignition After 60 sec, the new key is registered.
To code the Lock and un-lock:
Start with the key out of the ignition. Open the driver door
1. Perform these steps within 10 seconds:
-Insert the key into the ignition
- Pull key out
- Insert the key into the ignition
- Pull key out
2. Perform these steps within 45 seconds
- Close, then open the drivers door.
- Close, then open the drivers door.
3. Insert the key into the ignition and pull it out.
- Perform these steps within 40 seconds
- Close, then open the drivers door.
- Close, then open the drivers door.
- Insert the key into the ignition and leave in the ignition.
- Close the drivers door
- Turn the ignition to ON (not start), then back to off once (this enters add mode)
- Remove the key from the ignition.
5. The power door locks should lock then unlock automatically indicating successful entry into programming mode.
Return to step 1 if the locks did not cycle
6. Perform these steps within 40 seconds
-Press the lock and unlock buttons on the transmitter simultaneously for 1.5 seconds
-Immediately after letting go of the lock and unlock buttons, press the lock button by itself and hold for 2 seconds. (this needs to be done quite fast)
-The door locks should lock then unlock once indicating successful
programming. If the door locks cycle twice, repeat steps 6 as the remote was not accepted.
7. Open drivers door
Thanks for watching
Intro 00:00
Programming ignition 01:06
Programming door locks 02:25
Conclusion 02:58
7 ماه پیش
در تاریخ 1402/12/01 منتشر شده
است.
4,805
بـار بازدید شده