M601 M602 M603 Fuser & Maintenance Kit Replacement Instructions part number CF064-67901
95.1 هزار بار بازدید -
6 سال پیش
-
Today we will be reviewing
Today we will be reviewing the removal and installation process for the HP HP M601 M602 M603 Fuser & Maintenance Kit Replacement Instructions part number CF064-67901
Start by making sure the printer is off for at least 15 minutes and unplugged. Approach the printer from the front and open the tray door.
Suggested Tools
Flat head screwdriver
Magnetic tip phillips head
Kit Contents:
Kit Contents:
1 Transfer Roller: RM1-0699
4 Feed/Separation: Rollers RM1-0037
2 Pickup Rollers: RM1-0036
1 Fusing Assembly: RM1-8395
Repair Notes
The Page count Reset instructions will be located in the comments of the video or blog page so check below.
220,000 page yield
This fuser and kit is available at in an number of different options at metrofuser
Thanks for watching. If you would like to see more of these videos hit like and subscribe..Visit on Metrofuser's Youtube channel or http://www.metrofuser.com
HP M601 M602 M603 Maintenance Kit Replacement Instructions
This printer maintenance kit provides you with the most commonly used parts that wear. Replacing these worn parts will allow for maximum paper feed along with quality print performance.
Specifications:
Expected Duty Life: 200,000 pages
Kit Part Number: CF064-67901
------------ WARNING: Printer Parts May Be Hot -------------
Turn the printer off, unplug it, and allow it to sit for 30 minutes before
performing these maintenance procedures.
Transfer Roller Removal and Replacement
1. Open toner access door and tray 1.
2. Remove toner cartridge.
3. Lift the gear (left side) of the transfer roller up.
4. Slide to the left and remove.
5. Slide right side of replacement roller into right bushing.
6. Align left side collar making sure the open end is face down and push in.
CAUTION: Do not touch the surface of the transfer roller. Contact with skin can cause print quality problems..
Tray 2 Feed and Separation Roller Removal and Replacement
1. Remove the tray from the printer.
2. On the tray, lift the roller cover next to the roller.
3. Pinch the blue tab and slide the roller off the shaft.
4. Slide new roller on making sure the tab locks.
5. Locate the feed roller in the top of the tray cavity.
6. Repeat steps 3 and 4.
NOTE: The removal and replacement process are the same for the feed and separation rollers on tray 3 and the 1500
sheet feeder.
Fusing Assembly Removal and Replacement
1. Open rear output bin/face up tray.
2. Remove output bin from printer.
a.) Locate the left side hinge pin (there is a finger notch) squeeze the left hinge pin to the right to
release it from its mounting hole.
3. Slide the output bin to the left to remove from printer.
4. Pinch the blue tabs on the fuser and pull fuser out of printer.
5. Push the new fuser into the printer making sure both blue tabs lock.
6. Install the rear output bin/face up tray and check for proper operation.
Resetting the Maintenance Count
1. At the control panel, press the Home () button.
2. Use the down arrow button () to select ‘ADMINISTRATION’ then press the OK button.
3. Use the down arrow button to select ‘MANAGE SUPPLIES’ then press the OK button.
4. Use the down arrow button to select ‘RESET SUPPLIES’ then press the OK button.
5. Use the down arrow button to select ‘NEW MAINTENANCE KIT’ then press the OK button.
6. Use the down arrow button to select ‘YES’ then press the OK button.
7. The display should show ‘SETTINGS WERE SAVED SUCCESSFULLY’.
8. Print a configuration page. Ensure the ‘Pages since last maintenance’ entry is set to zero.
Start by making sure the printer is off for at least 15 minutes and unplugged. Approach the printer from the front and open the tray door.
Suggested Tools
Flat head screwdriver
Magnetic tip phillips head
Kit Contents:
Kit Contents:
1 Transfer Roller: RM1-0699
4 Feed/Separation: Rollers RM1-0037
2 Pickup Rollers: RM1-0036
1 Fusing Assembly: RM1-8395
Repair Notes
The Page count Reset instructions will be located in the comments of the video or blog page so check below.
220,000 page yield
This fuser and kit is available at in an number of different options at metrofuser
Thanks for watching. If you would like to see more of these videos hit like and subscribe..Visit on Metrofuser's Youtube channel or http://www.metrofuser.com
HP M601 M602 M603 Maintenance Kit Replacement Instructions
This printer maintenance kit provides you with the most commonly used parts that wear. Replacing these worn parts will allow for maximum paper feed along with quality print performance.
Specifications:
Expected Duty Life: 200,000 pages
Kit Part Number: CF064-67901
Turn the printer off, unplug it, and allow it to sit for 30 minutes before
performing these maintenance procedures.
Transfer Roller Removal and Replacement
1. Open toner access door and tray 1.
2. Remove toner cartridge.
3. Lift the gear (left side) of the transfer roller up.
4. Slide to the left and remove.
5. Slide right side of replacement roller into right bushing.
6. Align left side collar making sure the open end is face down and push in.
CAUTION: Do not touch the surface of the transfer roller. Contact with skin can cause print quality problems..
Tray 2 Feed and Separation Roller Removal and Replacement
1. Remove the tray from the printer.
2. On the tray, lift the roller cover next to the roller.
3. Pinch the blue tab and slide the roller off the shaft.
4. Slide new roller on making sure the tab locks.
5. Locate the feed roller in the top of the tray cavity.
6. Repeat steps 3 and 4.
NOTE: The removal and replacement process are the same for the feed and separation rollers on tray 3 and the 1500
sheet feeder.
Fusing Assembly Removal and Replacement
1. Open rear output bin/face up tray.
2. Remove output bin from printer.
a.) Locate the left side hinge pin (there is a finger notch) squeeze the left hinge pin to the right to
release it from its mounting hole.
3. Slide the output bin to the left to remove from printer.
4. Pinch the blue tabs on the fuser and pull fuser out of printer.
5. Push the new fuser into the printer making sure both blue tabs lock.
6. Install the rear output bin/face up tray and check for proper operation.
Resetting the Maintenance Count
1. At the control panel, press the Home () button.
2. Use the down arrow button () to select ‘ADMINISTRATION’ then press the OK button.
3. Use the down arrow button to select ‘MANAGE SUPPLIES’ then press the OK button.
4. Use the down arrow button to select ‘RESET SUPPLIES’ then press the OK button.
5. Use the down arrow button to select ‘NEW MAINTENANCE KIT’ then press the OK button.
6. Use the down arrow button to select ‘YES’ then press the OK button.
7. The display should show ‘SETTINGS WERE SAVED SUCCESSFULLY’.
8. Print a configuration page. Ensure the ‘Pages since last maintenance’ entry is set to zero.
6 سال پیش
در تاریخ 1397/11/18 منتشر شده
است.
95,117
بـار بازدید شده