Honda Ruckus Gy6 150cc Build and first Ride
66.6 هزار بار بازدید -
8 سال پیش
-
9/12/2016Gy6 swap for a honda
9/12/2016
Gy6 swap for a honda ruckus. i covered most of the things you will NEED for a basic gy6 swap. basic, meaning- CHEAP route/ everything you will NEED in order to ride with a gy6 if starting from nothing. More info below.
SUBSCRIBE!!!!!
If you already own a ruckus then heres all you will NEED to do this swap.
Motor mount:
$110+50 to welder. Or buy bolt on mount which will be $375+ depending on choice.
Gy6 motor: $350
Amazon
Drowsports
Ruck house
Makoa
Any ruckus manufacturer
Rear wheel- $120 if solid dish 7 or 8 inch (machinedmachines)
Rear tire- $60 140/70/12
Amazon
Rear hub: $135- $150
Machinedmachines
Mikuni fuel pump-$20
Amazon or ruckus site
3/16 fuel lines- $10
Amazon
24mm Oko carburetor-$80
Drowsports. Or can use stock carb which will be $25
Air filter- $5
Amazon
Gy6 riser/angles clocking flange- $40-50
Gy6 Throttle cable/slide throttle cable-amazon (silde throttle cable needed if oko carb is used) $30-$60
Gy6 exhaust-$90
Ebay (link in description)
Exhaust gasket- $5
Rear brake cable- 85'-87'
Amazon $30
Makoa wiring harness-$400
Makoascooters
Comes with everything you will need. Cdi box, coil, relay.
(Can also buy cheaper wiring harness for 150 such ass ATR, Dan max and others) makoa is most reliable IN MY OPINION and easiest to install.
Should be just under $1800 with the oko carb and slide throttle cable. (Remember you can save money on a harness but this one is a good one)
This swap uses drum brakes. Front disc brakes are highly recommended. Enjoy.
Link for exhaust: http://m.ebay.com/itm/SCOOTER-125CC-1... you will need to get a bracket to hold the can. Prob for 10 bucks max.
Gy6 swap for a honda ruckus. i covered most of the things you will NEED for a basic gy6 swap. basic, meaning- CHEAP route/ everything you will NEED in order to ride with a gy6 if starting from nothing. More info below.
SUBSCRIBE!!!!!
If you already own a ruckus then heres all you will NEED to do this swap.
Motor mount:
$110+50 to welder. Or buy bolt on mount which will be $375+ depending on choice.
Gy6 motor: $350
Amazon
Drowsports
Ruck house
Makoa
Any ruckus manufacturer
Rear wheel- $120 if solid dish 7 or 8 inch (machinedmachines)
Rear tire- $60 140/70/12
Amazon
Rear hub: $135- $150
Machinedmachines
Mikuni fuel pump-$20
Amazon or ruckus site
3/16 fuel lines- $10
Amazon
24mm Oko carburetor-$80
Drowsports. Or can use stock carb which will be $25
Air filter- $5
Amazon
Gy6 riser/angles clocking flange- $40-50
Gy6 Throttle cable/slide throttle cable-amazon (silde throttle cable needed if oko carb is used) $30-$60
Gy6 exhaust-$90
Ebay (link in description)
Exhaust gasket- $5
Rear brake cable- 85'-87'
Amazon $30
Makoa wiring harness-$400
Makoascooters
Comes with everything you will need. Cdi box, coil, relay.
(Can also buy cheaper wiring harness for 150 such ass ATR, Dan max and others) makoa is most reliable IN MY OPINION and easiest to install.
Should be just under $1800 with the oko carb and slide throttle cable. (Remember you can save money on a harness but this one is a good one)
This swap uses drum brakes. Front disc brakes are highly recommended. Enjoy.
Link for exhaust: http://m.ebay.com/itm/SCOOTER-125CC-1... you will need to get a bracket to hold the can. Prob for 10 bucks max.
8 سال پیش
در تاریخ 1395/06/24 منتشر شده
است.
66,632
بـار بازدید شده