Metal Roofing Flashing: How To Install Corrugated Metal Eave Trim + Drip Edge On A Metal Roof
265.4 هزار بار بازدید -
4 سال پیش
-
Learn How To Install Metal
Learn How To Install Metal Roofing Flashing. Eave Trim And Drip Edge Installation On A Metal Roof. STEP BY STEP INSTRUCTIONS for installation of drip edge and eave trim on an exposed fastener panel.
When you're installing a metal roof the drip edge or eave trim will be the first piece of trim and flashing that's installed. Installing the roofing panels will be done AFTER the eave flashing is installed. This video covers how to install eave trim and drip edge on a metal roof. Includes step by step metal roofing flashing installation instructions.
In this video we cover how to install metal roofing trim. We will demonstrate how to install eave flashing on a corrugated metal roofing panel. Learn how to cut the eave trim for the corner and roofing underlayment at the eave. Includes overlapping and fastening also.
This video specifically covers eave trim installation for an exposed fastener panel such as: ⅞” Corrugated, R Panel/PBR Panel, and Western Rib/7.2 Panel.
It is not intended for installation of standing seam panels.
This installation video for eave trim on a metal roof will cover:
00:00 How to install eave trim on a metal roof
00:25 What are the required tools and supplies to install eave flashing on a metal roof?
00:54 How to install eave trim at a corner
01:46 How to overlap eave trim for metal roof
01:56 How far should I overlap eave trim
02:26 How to fasten eave trim on a metal roof
03:37 Does drip edge go over or under underlayment?
If you already have not purchased your metal roofing give us a chance to bid your job. Save 15% to 50% with our manufacturer direct pricing and great customer service. Inexpensive delivery anywhere within the United States.
Visit Our WEBSITE
https://bit.ly/wsmr-website
Visit our LEARNING CENTER
http://bit.ly/learning-center-wsmr
Written Guide - Eave Trim Installation
https://bit.ly/eave-trim-installation
Download Our Install Guides
7/8" Corrugated
https://www.metalforroofing.com/docs/...
R Panel/PBR Panel
https://www.westernstatesmetalroofing...
Western Rib/7.2 Panel
https://www.westernstatesmetalroofing...
Installing Eave Trim On A Metal Roof. Step By Step Guide.
https://bit.ly/eave-trim-installation
This metal roofing eave installation video will also cover:
Removing plastic from eave trim
How to cut eave trim at corner
How to bend corner at eave
How to notch eave trim at overlap
What type of screw should I use to fasten eave trim
Screw placement eave trim
How to apply caulking at eave trim overlap
What type of roofing underlayment do I use at eave trim
Installing Eave Trim At A Corner
•Start on the left side of the roof
•Remove the protective plastic film from the eave trim.
•Run the eave trim one inch past the edge of the roof.
•Take your carpenters pencil and mark the underside of the eave trim by tracing the fascia and gable board. The line you created is the bend line.
•Use your snips and cut the center of the eave trim until you get to the bend line.
•Cut away the top part of the eave trim that sits on top of the roof.
•Remove the hem by making a 45 degree angled cut to the bend line. This will allow the eave trim to meet up with the gable trim and have a clean mitered corner.
•User your hand seamer to bend the remaining edge upwards.
•Install the drip edge on the roof so that the piece that you bent with the seamer tool folds around the corner.
Overlapping Two Pieces Of Eave Trim On A Metal Roof
•Notch eave trim by removing three inches of the drip edge hem.
This allows it to slide into the next piece of eave trim.
The purpose is to create a secure fit on the fascia that will not blow around in the wind.
•Apply caulking where the eave flashing will overlap
•Install the second piece of eave trim by taking a screwdriver and slightly opening the hem.
•Then slide the second piece of eave trim into the first piece.
Fastening Eave Trim On A Metal Roof
•Use a 1” metal to wood pancake head screw to fasten the top of the eave trim to the metal roof.
•The screw spacing is one screw located at 8" from each end of the eave flashing. In between both ends of the eave flashing the screws should be spaced at 12" OC center.
Similar Videos and products:
Max-Rib and Master-Rib. American Building Components and ABC Metal Roofing, McElroy Metals, RoofingIntelligence.com, The Metal Roofing Channel, And Mackey Metal Roofing.
FOLLOW US ON SOCIAL MEDIA:
FACEBOOK: https://bit.ly/facebook-wsmr
INSTAGRAM: https://bit.ly/instagram-wsmr
TWITTER: https://bit.ly/twitter-wsmr
LINKEDIN: https://bit.ly/linkinin-wsmr
HOUZZ: https://bit.ly/houzz-wsmr
PINTEREST: https://bit.ly/pinterest-wsmr
YOUTUBE: https://bit.ly/youtube-wsmr
Visit Our WEBSITE
https://bit.ly/wsmr-website
Visit our LEARNING CENTER
http://bit.ly/learning-center-wsmr
When you're installing a metal roof the drip edge or eave trim will be the first piece of trim and flashing that's installed. Installing the roofing panels will be done AFTER the eave flashing is installed. This video covers how to install eave trim and drip edge on a metal roof. Includes step by step metal roofing flashing installation instructions.
In this video we cover how to install metal roofing trim. We will demonstrate how to install eave flashing on a corrugated metal roofing panel. Learn how to cut the eave trim for the corner and roofing underlayment at the eave. Includes overlapping and fastening also.
This video specifically covers eave trim installation for an exposed fastener panel such as: ⅞” Corrugated, R Panel/PBR Panel, and Western Rib/7.2 Panel.
It is not intended for installation of standing seam panels.
This installation video for eave trim on a metal roof will cover:
00:00 How to install eave trim on a metal roof
00:25 What are the required tools and supplies to install eave flashing on a metal roof?
00:54 How to install eave trim at a corner
01:46 How to overlap eave trim for metal roof
01:56 How far should I overlap eave trim
02:26 How to fasten eave trim on a metal roof
03:37 Does drip edge go over or under underlayment?
If you already have not purchased your metal roofing give us a chance to bid your job. Save 15% to 50% with our manufacturer direct pricing and great customer service. Inexpensive delivery anywhere within the United States.
Visit Our WEBSITE
https://bit.ly/wsmr-website
Visit our LEARNING CENTER
http://bit.ly/learning-center-wsmr
Written Guide - Eave Trim Installation
https://bit.ly/eave-trim-installation
Download Our Install Guides
7/8" Corrugated
https://www.metalforroofing.com/docs/...
R Panel/PBR Panel
https://www.westernstatesmetalroofing...
Western Rib/7.2 Panel
https://www.westernstatesmetalroofing...
Installing Eave Trim On A Metal Roof. Step By Step Guide.
https://bit.ly/eave-trim-installation
This metal roofing eave installation video will also cover:
Removing plastic from eave trim
How to cut eave trim at corner
How to bend corner at eave
How to notch eave trim at overlap
What type of screw should I use to fasten eave trim
Screw placement eave trim
How to apply caulking at eave trim overlap
What type of roofing underlayment do I use at eave trim
Installing Eave Trim At A Corner
•Start on the left side of the roof
•Remove the protective plastic film from the eave trim.
•Run the eave trim one inch past the edge of the roof.
•Take your carpenters pencil and mark the underside of the eave trim by tracing the fascia and gable board. The line you created is the bend line.
•Use your snips and cut the center of the eave trim until you get to the bend line.
•Cut away the top part of the eave trim that sits on top of the roof.
•Remove the hem by making a 45 degree angled cut to the bend line. This will allow the eave trim to meet up with the gable trim and have a clean mitered corner.
•User your hand seamer to bend the remaining edge upwards.
•Install the drip edge on the roof so that the piece that you bent with the seamer tool folds around the corner.
Overlapping Two Pieces Of Eave Trim On A Metal Roof
•Notch eave trim by removing three inches of the drip edge hem.
This allows it to slide into the next piece of eave trim.
The purpose is to create a secure fit on the fascia that will not blow around in the wind.
•Apply caulking where the eave flashing will overlap
•Install the second piece of eave trim by taking a screwdriver and slightly opening the hem.
•Then slide the second piece of eave trim into the first piece.
Fastening Eave Trim On A Metal Roof
•Use a 1” metal to wood pancake head screw to fasten the top of the eave trim to the metal roof.
•The screw spacing is one screw located at 8" from each end of the eave flashing. In between both ends of the eave flashing the screws should be spaced at 12" OC center.
Similar Videos and products:
Max-Rib and Master-Rib. American Building Components and ABC Metal Roofing, McElroy Metals, RoofingIntelligence.com, The Metal Roofing Channel, And Mackey Metal Roofing.
FOLLOW US ON SOCIAL MEDIA:
FACEBOOK: https://bit.ly/facebook-wsmr
INSTAGRAM: https://bit.ly/instagram-wsmr
TWITTER: https://bit.ly/twitter-wsmr
LINKEDIN: https://bit.ly/linkinin-wsmr
HOUZZ: https://bit.ly/houzz-wsmr
PINTEREST: https://bit.ly/pinterest-wsmr
YOUTUBE: https://bit.ly/youtube-wsmr
Visit Our WEBSITE
https://bit.ly/wsmr-website
Visit our LEARNING CENTER
http://bit.ly/learning-center-wsmr
4 سال پیش
در تاریخ 1398/12/06 منتشر شده
است.
265,439
بـار بازدید شده