How to rebuild Thrustmaster TX & T300
21.9 هزار بار بازدید -
2 سال پیش
-
link to pictures of the
link to pictures of the control board connections and internal layout for rebuild guides as well as rehost of the Motor calibration software and calibration software guide: https://drive.google.com/drive/folder...
replacment bearings and bearing mod bearing sizes, you do not need to order from the links, I have put the sizes for each that can be sourced from your choice of bearing supplier, links are just for those who want an easy way to order.
Front Wheel hub bearing replacment need 1
68072ZZ size (35mmx47mmx7mm)
https://www.amazon.com/Shielded-Beari...
Rear wheel hub bearing replacment need 1
68052ZZ size (25mmx37mmx7mm)
https://www.amazon.com/uxcell-Bearing...
Motor belt tensioner roller bearing mod uses 6 bearings
MR93ZZ size (3mmx9mmx4mm)
https://www.amazon.com/XIKE-Bearings-...
Lower Wheel drive belt tensioner roller bearing mod uses 6 bearings
695ZZ size (5mmx13mmx4mm) please see note below for T300 wheels doing this mod
https://www.amazon.com/uxcell-Groove-...
Note about T300 wheels if doing the lower bearing mod
I was told by another youtuber that the T300 lower roller axles are slighty different from the TX base ones and that they had to cut and make new axles as the original axles get smaller in the middle and won't support the bearings properly. You should not need to do this on the TX base, only if you have a T300 base. link for an appropriate sized rod to fabricate new axles below, a manual hand saw will work fine to cut it as it is very thin metal, cut to the same length as the stock lower tensioner axles and install the same way as originals.
https://www.amazon.com/uxcell-100mm-S...
Dielectric grease to lubricate wheel internals, or any plastic safe grease can be used, if unsure use dielectric or silicon grease.
https://www.amazon.com/Super-Lube-820...
replacment bearings and bearing mod bearing sizes, you do not need to order from the links, I have put the sizes for each that can be sourced from your choice of bearing supplier, links are just for those who want an easy way to order.
Front Wheel hub bearing replacment need 1
68072ZZ size (35mmx47mmx7mm)
https://www.amazon.com/Shielded-Beari...
Rear wheel hub bearing replacment need 1
68052ZZ size (25mmx37mmx7mm)
https://www.amazon.com/uxcell-Bearing...
Motor belt tensioner roller bearing mod uses 6 bearings
MR93ZZ size (3mmx9mmx4mm)
https://www.amazon.com/XIKE-Bearings-...
Lower Wheel drive belt tensioner roller bearing mod uses 6 bearings
695ZZ size (5mmx13mmx4mm) please see note below for T300 wheels doing this mod
https://www.amazon.com/uxcell-Groove-...
Note about T300 wheels if doing the lower bearing mod
I was told by another youtuber that the T300 lower roller axles are slighty different from the TX base ones and that they had to cut and make new axles as the original axles get smaller in the middle and won't support the bearings properly. You should not need to do this on the TX base, only if you have a T300 base. link for an appropriate sized rod to fabricate new axles below, a manual hand saw will work fine to cut it as it is very thin metal, cut to the same length as the stock lower tensioner axles and install the same way as originals.
https://www.amazon.com/uxcell-100mm-S...
Dielectric grease to lubricate wheel internals, or any plastic safe grease can be used, if unsure use dielectric or silicon grease.
https://www.amazon.com/Super-Lube-820...
2 سال پیش
در تاریخ 1401/05/16 منتشر شده
است.
21,997
بـار بازدید شده