Long Range FPV Antennas for ELRS & Crossfire + Diversity RX
4.8 هزار بار بازدید -
6 ماه پیش
-
Anyone who's serious about flying
Anyone who's serious about flying long range FPV should consider using a diversity receiver with a vertically polarized RX antenna. For both Express LRS & Crossfire this second antenna is most often mounted vertically at the back of the drone, beside the video antenna. It will help to improve the quality of the communication link between transmitter and receiver as well as minimize the chances of a failsafe (total loss of control). We're going to make a 915/868mhz dipole antenna from scratch.
My Long Range FPV frame designs:
-Falcon RPM 7.5" Cinematic / Long Range @ AddictiveRC - https://bit.ly/Falcon_RPM_AddictiveRC
-Falcon RPM 7.5" Cinematic / Long Range @ CNCDrones - https://bit.ly/FalconRPM
- RAD Li-ion 7" Long Range - https://bit.ly/3MFoCdg
- RAD Scout 7" Xtra Long Range - http://bit.ly/3kyvPDy
- AOS Falcon 7 Cinematic Long Range - https://bit.ly/3jUiLUI
Parts list and affiliate links for 6s long range build - (great reliability and balance between power and efficiency)
T-Motor F7 Pro flight controller - https://bit.ly/3xtW1mE
T-Motor F55 Pro II ESC (4in1) - https://bit.ly/3uITNOF
Motors for 7" props: T Motor F90 2806.5 1300kv - https://bit.ly/3M4fjDg
Motors for 7.5" props: T-Motor Velox 3008 1500kv - https://bit.ly/3QJ8Gcf
Camera Butter ND Filters - http://bit.ly/3WZmSQR
7" props for RAD Scout - Gemfan 7035 (tri-blade) - https://bit.ly/3vdSzKu
7" props for RAD Li-ion - Gemfan 7037 (tri-blade) - https://bit.ly/3rvCz5f
7" props for Falcon 7 - Gemfan 7040 (tri-blades) - http://bit.ly/3YaxFrZ
7.5" props for Falcon RPM Gemfan 7535 (tri-blades) - https://bit.ly/3vdSzKu
VTX antenna TrueRC Singularity - https://bit.ly/3xvXFEg
VTX - https://bit.ly/3JHWW5l
Receiver - https://bit.ly/3xuMGv8
FPV camera (analog) - https://bit.ly/3JL88OT
GPS - https://bit.ly/3uJjRci
Receiver antenna - https://bit.ly/3jG7o2L
Video Chapters:
00:00 - Introduction / using a diversity antenna
02:05 - Required materials
03:45 - Cutting SMA extension to length
05:45 - Stripping the outer shielding
08:30 - Adding heat shrink & antenna stiffness
13:30 - Counter element (made from shielding)
15:45 - More heat shrink
17:12 - Installing counter element
20:45 - Important note about antenna construction
21:25 - Make sure the elements are properly sized
22:22 - Conclusion
Consider supporting the channel on Patreon:
https://www.patreon.com/user?u=48131636
Check out my frame design page @ CNCDrones: https://bit.ly/3vvRrD7
Use this link for the purchase of anything from GetFPV with no extra cost to you, but it helps the channel out: https://bit.ly/3roKZui
My Long Range FPV frame designs:
-Falcon RPM 7.5" Cinematic / Long Range @ AddictiveRC - https://bit.ly/Falcon_RPM_AddictiveRC
-Falcon RPM 7.5" Cinematic / Long Range @ CNCDrones - https://bit.ly/FalconRPM
- RAD Li-ion 7" Long Range - https://bit.ly/3MFoCdg
- RAD Scout 7" Xtra Long Range - http://bit.ly/3kyvPDy
- AOS Falcon 7 Cinematic Long Range - https://bit.ly/3jUiLUI
Parts list and affiliate links for 6s long range build - (great reliability and balance between power and efficiency)
T-Motor F7 Pro flight controller - https://bit.ly/3xtW1mE
T-Motor F55 Pro II ESC (4in1) - https://bit.ly/3uITNOF
Motors for 7" props: T Motor F90 2806.5 1300kv - https://bit.ly/3M4fjDg
Motors for 7.5" props: T-Motor Velox 3008 1500kv - https://bit.ly/3QJ8Gcf
Camera Butter ND Filters - http://bit.ly/3WZmSQR
7" props for RAD Scout - Gemfan 7035 (tri-blade) - https://bit.ly/3vdSzKu
7" props for RAD Li-ion - Gemfan 7037 (tri-blade) - https://bit.ly/3rvCz5f
7" props for Falcon 7 - Gemfan 7040 (tri-blades) - http://bit.ly/3YaxFrZ
7.5" props for Falcon RPM Gemfan 7535 (tri-blades) - https://bit.ly/3vdSzKu
VTX antenna TrueRC Singularity - https://bit.ly/3xvXFEg
VTX - https://bit.ly/3JHWW5l
Receiver - https://bit.ly/3xuMGv8
FPV camera (analog) - https://bit.ly/3JL88OT
GPS - https://bit.ly/3uJjRci
Receiver antenna - https://bit.ly/3jG7o2L
Video Chapters:
00:00 - Introduction / using a diversity antenna
02:05 - Required materials
03:45 - Cutting SMA extension to length
05:45 - Stripping the outer shielding
08:30 - Adding heat shrink & antenna stiffness
13:30 - Counter element (made from shielding)
15:45 - More heat shrink
17:12 - Installing counter element
20:45 - Important note about antenna construction
21:25 - Make sure the elements are properly sized
22:22 - Conclusion
Consider supporting the channel on Patreon:
https://www.patreon.com/user?u=48131636
Check out my frame design page @ CNCDrones: https://bit.ly/3vvRrD7
Use this link for the purchase of anything from GetFPV with no extra cost to you, but it helps the channel out: https://bit.ly/3roKZui
6 ماه پیش
در تاریخ 1402/11/07 منتشر شده
است.
4,875
بـار بازدید شده