My Nissan 350Z Gets The Complete Service Overhaul
120.2 هزار بار بازدید -
6 سال پیش
-
This week:How to change differential
This week:
How to change differential oil.
How to change transmission oil.
How to change engine oil and filter.
How to change spark plugs.
How to change coolant.
How to clean the MAF sensor.
How to clean the throttle body.
If you'd like to help us be able to make shows more often please consider donating via Patreon:
Patreon: roadandracetv
Check out our social media for more content:
Twitter - Twitter: roadandracetv
Facebook - Facebook: RoadandRaceTV
Instagram - Instagram: roadandracetv
Website - https://road-and-race.co.uk
The tools used in this video can be found here:
http://road-and-race.co.uk/tools
350Z bolt torque settings:
Manual gearbox drain and filler plugs - 34 Nm
Engine oil drain plug - 35 Nm
Engine oil filter - 18 Nm
Spark plugs - 25 Nm
Differential drain and filler plugs - 34 Nm
350Z coolant bleeding process:
1.Remove air relief plug on heater hose.
2. Fill radiator and reservoir tank to specified level. Pour engine coolant through coolant filler neck slowly of less than 2 (2-1/8US qt,1-3/4 lmp qt) a minute to allow
air in system to escape.
3. When engine coolant overflows air relief hole on heater hose,
install air relief plug with new O-ring.
4. Warm up engine to normal operating temperature with radiator cap installed.
5. Run engine at 3,000 rpm for 10 seconds and return to idle speed. Repeat two or three times.
6. Stop engine and cool down to less than approximately 50°C (122°F). If necessary, refill radiator up to filler neck with engine coolant.
7. Refill reservoir tank to MAX level line with engine coolant.
8. Repeat steps 1 through 6 two or more times with radiator cap installed until engine coolant level no longer drops.
9. Check cooling system for leaks with engine running.
10. Warm up engine, and check for sound of engine coolant flow while running engine from idle up to 3,000 rpm with heater temperature controller set at several position between COOL and WARM. Sound may be noticeable at heater unit.
11. Repeat step 11 three times.
12. If sound is heard, bleed air from cooling system by repeating step 4 through 7 until engine coolant level no longer drops.
How to change differential oil.
How to change transmission oil.
How to change engine oil and filter.
How to change spark plugs.
How to change coolant.
How to clean the MAF sensor.
How to clean the throttle body.
If you'd like to help us be able to make shows more often please consider donating via Patreon:
Patreon: roadandracetv
Check out our social media for more content:
Twitter - Twitter: roadandracetv
Facebook - Facebook: RoadandRaceTV
Instagram - Instagram: roadandracetv
Website - https://road-and-race.co.uk
The tools used in this video can be found here:
http://road-and-race.co.uk/tools
350Z bolt torque settings:
Manual gearbox drain and filler plugs - 34 Nm
Engine oil drain plug - 35 Nm
Engine oil filter - 18 Nm
Spark plugs - 25 Nm
Differential drain and filler plugs - 34 Nm
350Z coolant bleeding process:
1.Remove air relief plug on heater hose.
2. Fill radiator and reservoir tank to specified level. Pour engine coolant through coolant filler neck slowly of less than 2 (2-1/8US qt,1-3/4 lmp qt) a minute to allow
air in system to escape.
3. When engine coolant overflows air relief hole on heater hose,
install air relief plug with new O-ring.
4. Warm up engine to normal operating temperature with radiator cap installed.
5. Run engine at 3,000 rpm for 10 seconds and return to idle speed. Repeat two or three times.
6. Stop engine and cool down to less than approximately 50°C (122°F). If necessary, refill radiator up to filler neck with engine coolant.
7. Refill reservoir tank to MAX level line with engine coolant.
8. Repeat steps 1 through 6 two or more times with radiator cap installed until engine coolant level no longer drops.
9. Check cooling system for leaks with engine running.
10. Warm up engine, and check for sound of engine coolant flow while running engine from idle up to 3,000 rpm with heater temperature controller set at several position between COOL and WARM. Sound may be noticeable at heater unit.
11. Repeat step 11 three times.
12. If sound is heard, bleed air from cooling system by repeating step 4 through 7 until engine coolant level no longer drops.
6 سال پیش
در تاریخ 1397/07/12 منتشر شده
است.
120,282
بـار بازدید شده