How to Make a Posable Mannequin | I Like To Make Stuff
377.7 هزار بار بازدید -
6 سال پیش
-
For the past 2 years,
For the past 2 years, I've been building a fully-3d printed set of Shoretrooper armor. It is time to build a posable mannequin so he can become a life-size action figure!
PUNISHED PROPS ACADEMY
Custom Mannequin Display - Sweeper Bo...
TOOLS & SUPPLIES (affiliate links):
https://kit.co/iliketomakestuff/my-wo...
https://kit.co/iliketomakestuff/shop-...
MUSIC: http://share.epidemicsound.com/iltms
Because this armor set was scaled to fit my body, I had to measure my extremities to get an accurate mannequin. Josh marked out my arms, legs, collar bone, and torso lengths with tape while I laid on the floor. We used these measurements as the basis for the PVC pipe segments that would make up the skeleton.
Because I want Dan to be able to stand in different poses I needed to factor in some moveable joints. Like a good trooper he is, Dan will always be carrying his rifle in this right hand. That arm should articulate a little, but it needs to be more rigid and strong. The left hand should be more flexible and posable so he can hold the rifle, point at rebel scum, or wave to his fictitious brother Gil. The knees should also bend slightly depending on certain action poses.
With these joints in mind, we found some simple PVC solutions at Lowe's. By using threaded unions that can be tightened into different positions, we can give a full range of arm motions when placed in the right location. Placing the unions on the outer collar bone allows the arm to move forward and back, and by adding one to the bicep, the elbows and forearms can rotate. The wrists will be made separately so they can rotate freely. The knees simply need to move forward and backward.
Because this skeleton is made of PVC, I can decide which pieces need to be glued in place and which ones should be held with friction. The non-glued joints allow for some level of articulation in places like the hips, the thighs, and the feet.
Using the taped-off measurements we made earlier, I began cutting the PVC "bones." I used thicker PVC as a spine to support the rest of the mannequin, a 4-way unions to attach the collar bones and the neck, and a T-union to attach the hips. Using a combination of 45- & 90-degree unions, we made the rigid right arm and also portions of the shoulders and hips.
Josh modeled and 3d printed some simple posable joints. We used these parts as unions between the PVC pipe that tightened into placed using a 1/4-20 bolts and wing nut. These parts made up the left elbow and the two knees.
I had an old piece of cherry butcher block that will act as the base. While the PVC pipe skeleton is versatile and posable, it isn't strong enough to stand on its own. To hold it upright, I needed to make a support beam that attaches to the base and holds Dan up. I chose to use some 1 1/4" angle iron I had left over. I cut a slot in the butcher block base and mounted the beam from underneath using a small plate.
To mount the skeleton to the beam, I needed to add an offset spacer. I used small cutoff pieces of the angle iron welded together to give Dan a stand-off gap. This gap is necessary because I couldn't pull his pants up if the beam were mounted straight to the spine. Dan was fixed to the beam using pipe clamps so he could be adjusted up or down.
Depending on your costume, it may be very necessary to add padding or musculature to your PVC skeleton. The armor set needs to be supported by a built-out torso and hip structure. The belt, abdomen plate, and chest cover need to sit against dense padding so that it won't fall down. I used some spare packing foam cut to size and taped into place to build up this structure. Left-over foam pool noodles were used on the arms to mimic my super-buff biceps.
Lastly, It was time for Dan to get suited up. Because many of the larger pieces were friction fit together, they came apart easily so I could get the clothes on. Piece by piece the whole armor set came together. As designed, we were able to loosen and tighten the PVC unions with the cloths on to change Dan's posture. The the armature hands were able to grip the rifle perfectly and the rigid right arm help the weapon without drooping.
Subscribe: http://bit.ly/ILikeToMakestuffSubscribe
Check out my TopVideos!: http://bit.ly/ILikeToMakeStuffTopVideos
Learn 3d modeling, get digital plans, and cool merch at
https://iliketomakestuff.com
Want to support ILTMS? Get exclusive content and more...
http://www.iliketomakestuff.com/patreon
FOLLOW:
Instagram: iliketomakestuff
Twitter: iliketomakestuff
Facebook: iltms
#ILikeToMakeStuff
About I Like To Make Stuff:
We have lots of projects including woodworking, metalworking, electronics, 3D printing, prop making and more!
These videos are our attempt inspire and empower others to make the stuff that they want to have. Hopefully you'll see something here that will inspire you to make something that you're passionate about!
PUNISHED PROPS ACADEMY
Custom Mannequin Display - Sweeper Bo...
TOOLS & SUPPLIES (affiliate links):
https://kit.co/iliketomakestuff/my-wo...
https://kit.co/iliketomakestuff/shop-...
MUSIC: http://share.epidemicsound.com/iltms
Because this armor set was scaled to fit my body, I had to measure my extremities to get an accurate mannequin. Josh marked out my arms, legs, collar bone, and torso lengths with tape while I laid on the floor. We used these measurements as the basis for the PVC pipe segments that would make up the skeleton.
Because I want Dan to be able to stand in different poses I needed to factor in some moveable joints. Like a good trooper he is, Dan will always be carrying his rifle in this right hand. That arm should articulate a little, but it needs to be more rigid and strong. The left hand should be more flexible and posable so he can hold the rifle, point at rebel scum, or wave to his fictitious brother Gil. The knees should also bend slightly depending on certain action poses.
With these joints in mind, we found some simple PVC solutions at Lowe's. By using threaded unions that can be tightened into different positions, we can give a full range of arm motions when placed in the right location. Placing the unions on the outer collar bone allows the arm to move forward and back, and by adding one to the bicep, the elbows and forearms can rotate. The wrists will be made separately so they can rotate freely. The knees simply need to move forward and backward.
Because this skeleton is made of PVC, I can decide which pieces need to be glued in place and which ones should be held with friction. The non-glued joints allow for some level of articulation in places like the hips, the thighs, and the feet.
Using the taped-off measurements we made earlier, I began cutting the PVC "bones." I used thicker PVC as a spine to support the rest of the mannequin, a 4-way unions to attach the collar bones and the neck, and a T-union to attach the hips. Using a combination of 45- & 90-degree unions, we made the rigid right arm and also portions of the shoulders and hips.
Josh modeled and 3d printed some simple posable joints. We used these parts as unions between the PVC pipe that tightened into placed using a 1/4-20 bolts and wing nut. These parts made up the left elbow and the two knees.
I had an old piece of cherry butcher block that will act as the base. While the PVC pipe skeleton is versatile and posable, it isn't strong enough to stand on its own. To hold it upright, I needed to make a support beam that attaches to the base and holds Dan up. I chose to use some 1 1/4" angle iron I had left over. I cut a slot in the butcher block base and mounted the beam from underneath using a small plate.
To mount the skeleton to the beam, I needed to add an offset spacer. I used small cutoff pieces of the angle iron welded together to give Dan a stand-off gap. This gap is necessary because I couldn't pull his pants up if the beam were mounted straight to the spine. Dan was fixed to the beam using pipe clamps so he could be adjusted up or down.
Depending on your costume, it may be very necessary to add padding or musculature to your PVC skeleton. The armor set needs to be supported by a built-out torso and hip structure. The belt, abdomen plate, and chest cover need to sit against dense padding so that it won't fall down. I used some spare packing foam cut to size and taped into place to build up this structure. Left-over foam pool noodles were used on the arms to mimic my super-buff biceps.
Lastly, It was time for Dan to get suited up. Because many of the larger pieces were friction fit together, they came apart easily so I could get the clothes on. Piece by piece the whole armor set came together. As designed, we were able to loosen and tighten the PVC unions with the cloths on to change Dan's posture. The the armature hands were able to grip the rifle perfectly and the rigid right arm help the weapon without drooping.
Subscribe: http://bit.ly/ILikeToMakestuffSubscribe
Check out my TopVideos!: http://bit.ly/ILikeToMakeStuffTopVideos
Learn 3d modeling, get digital plans, and cool merch at
https://iliketomakestuff.com
Want to support ILTMS? Get exclusive content and more...
http://www.iliketomakestuff.com/patreon
FOLLOW:
Instagram: iliketomakestuff
Twitter: iliketomakestuff
Facebook: iltms
#ILikeToMakeStuff
About I Like To Make Stuff:
We have lots of projects including woodworking, metalworking, electronics, 3D printing, prop making and more!
These videos are our attempt inspire and empower others to make the stuff that they want to have. Hopefully you'll see something here that will inspire you to make something that you're passionate about!
6 سال پیش
در تاریخ 1397/08/24 منتشر شده
است.
377,751
بـار بازدید شده