1:12 scale DIY, Easy, dollhouse miniature project making tea lights & candle warmers, LED ready
1.7 هزار بار بازدید -
3 سال پیش
-
Welcome to the video!This is
Welcome to the video!
This is a 1:12 scale DIY, Easy, dollhouse project making tea lights, candle warmers & votives LED ready using quilling paper, pony beads & fiber optic strands.
The video shows one way to make tea lights, candle warmers & votives for dollhouse miniature. It is helpful to consider locations for display so you can plan on the light source access & set-up.
Materials List:
1. quilling paper - white, cream, silver or your choice in 1/8 inch strips, (3 inch piece for each tea light & 1 3/8 inch piece for small votive tea light) I used 1/4 silver strips for aluminum cup wraps.
2. tea lights: cut ten 3 inch white pieces, votives: cut two 1 3/8 inch white pieces (adjust for bead interior)
3. tea light exterior: two 1/2 inch silver pieces to look like aluminum cups, 1/4 quilling strip width
4. fiber optic strands - thin about diameter size of quilter or sewing pin, about four inches, end flow filament, 0.25 to 0.5 mm from evandesigns.com or your choice. The strands are strong but can bend or snap, use gently.
5. pony beads - two 6 x 9 mm with 4mm hole for each candle warmer: one clear & other a solid color; or one clear 4 x 7 mm with 2.5mm hole for votive; (need two clear 6 x 9 & two solid and two clear 4 x 7)
6. light power source - lighting kit with warm white chip or nano, compact switch & coin cell holder from evandesigns.com or your choice. Note: The tea light, candle warmers or votives display area will need an access point below base to light through fiber optic strand. If on a countertop, table, shelf or window sill, drill a hole to place candle over & place light power source under in a drawer or cabinet or the candle warmer back side drilled hole access point to insert. The number of kits depends on your display. The company website has useful videos.
7. optional base ideas - card stock, silver quilling paper strip, pony bead, other beads, wood The bottom will need to be open so fiber optic strand can receive light.
8. glue - PVA clear drying, E6000 Bead & Jewelry glue
9. toothpicks - for gluing
10. containers - like plastic lids to hold glue
11. clamps
12. tweezers
13. craft knife & mat & scissors
14. stylus & foam piece
15. drill & bit - small, to go through pony bead or base side
16. ruler & pencil
Optional accessories:
a. copy paper - to punch or cut decorations
b card stock - to punch base decor like flower shape in assorted colors, approximately 2 x 3 inch piece for two flower piece color
c. acrylic paints - to color decorations or candles
d. paper punches - shapes for decorations or candle base, small flower approximately 3/8 inch diameter, two pieces each, see video
e. stickers - ideas for decorations: dragonflies, butterflies, flowers, leaves, suns, stars, hearts & many others, may need to apply with super glue or bead glue
f. permanent markers - to color decorations or candles, or color flame end of fiber optic (I did not color ends)
g. jewelry findings & bits - jump rings that can be removable decor
h. artificial snow - decorations, color with paints
i. no hole bits
Notes:
*supplies & materials available online or at your local arts & crafts stores, large department stores or miniature shows
*sizes are close approximations
*the tea light, candle warmer or votive display area will need an access point below pillar to light through fiber optic strand. If on a countertop, table, shelf or window sill, drill a hole to place candle over & place light power source under in a drawer or cabinet.
Uses ideas:
*1:12 miniature diorama displays, stores, shops, kitchens, room boxes, living & family rooms, bedrooms, bathrooms, offices & gifts for special events
*club projects or activities - non commercial purposes
I hope you like & share this project making tea lights & candle warmers & votives.
…Look for my upcoming 1:12 scale projects…including more from the wildflower series and spice holders with containers…
Thank you for watching,
Cathy
Miniaturist
This is a 1:12 scale DIY, Easy, dollhouse project making tea lights, candle warmers & votives LED ready using quilling paper, pony beads & fiber optic strands.
The video shows one way to make tea lights, candle warmers & votives for dollhouse miniature. It is helpful to consider locations for display so you can plan on the light source access & set-up.
Materials List:
1. quilling paper - white, cream, silver or your choice in 1/8 inch strips, (3 inch piece for each tea light & 1 3/8 inch piece for small votive tea light) I used 1/4 silver strips for aluminum cup wraps.
2. tea lights: cut ten 3 inch white pieces, votives: cut two 1 3/8 inch white pieces (adjust for bead interior)
3. tea light exterior: two 1/2 inch silver pieces to look like aluminum cups, 1/4 quilling strip width
4. fiber optic strands - thin about diameter size of quilter or sewing pin, about four inches, end flow filament, 0.25 to 0.5 mm from evandesigns.com or your choice. The strands are strong but can bend or snap, use gently.
5. pony beads - two 6 x 9 mm with 4mm hole for each candle warmer: one clear & other a solid color; or one clear 4 x 7 mm with 2.5mm hole for votive; (need two clear 6 x 9 & two solid and two clear 4 x 7)
6. light power source - lighting kit with warm white chip or nano, compact switch & coin cell holder from evandesigns.com or your choice. Note: The tea light, candle warmers or votives display area will need an access point below base to light through fiber optic strand. If on a countertop, table, shelf or window sill, drill a hole to place candle over & place light power source under in a drawer or cabinet or the candle warmer back side drilled hole access point to insert. The number of kits depends on your display. The company website has useful videos.
7. optional base ideas - card stock, silver quilling paper strip, pony bead, other beads, wood The bottom will need to be open so fiber optic strand can receive light.
8. glue - PVA clear drying, E6000 Bead & Jewelry glue
9. toothpicks - for gluing
10. containers - like plastic lids to hold glue
11. clamps
12. tweezers
13. craft knife & mat & scissors
14. stylus & foam piece
15. drill & bit - small, to go through pony bead or base side
16. ruler & pencil
Optional accessories:
a. copy paper - to punch or cut decorations
b card stock - to punch base decor like flower shape in assorted colors, approximately 2 x 3 inch piece for two flower piece color
c. acrylic paints - to color decorations or candles
d. paper punches - shapes for decorations or candle base, small flower approximately 3/8 inch diameter, two pieces each, see video
e. stickers - ideas for decorations: dragonflies, butterflies, flowers, leaves, suns, stars, hearts & many others, may need to apply with super glue or bead glue
f. permanent markers - to color decorations or candles, or color flame end of fiber optic (I did not color ends)
g. jewelry findings & bits - jump rings that can be removable decor
h. artificial snow - decorations, color with paints
i. no hole bits
Notes:
*supplies & materials available online or at your local arts & crafts stores, large department stores or miniature shows
*sizes are close approximations
*the tea light, candle warmer or votive display area will need an access point below pillar to light through fiber optic strand. If on a countertop, table, shelf or window sill, drill a hole to place candle over & place light power source under in a drawer or cabinet.
Uses ideas:
*1:12 miniature diorama displays, stores, shops, kitchens, room boxes, living & family rooms, bedrooms, bathrooms, offices & gifts for special events
*club projects or activities - non commercial purposes
I hope you like & share this project making tea lights & candle warmers & votives.
…Look for my upcoming 1:12 scale projects…including more from the wildflower series and spice holders with containers…
Thank you for watching,
Cathy
Miniaturist
3 سال پیش
در تاریخ 1400/09/30 منتشر شده
است.
1,778
بـار بازدید شده