03-Beginners guide to building The MPCNC machine Part03 - Z-axis block And the middle section.
1.5 هزار بار بازدید -
4 سال پیش
-
Beginners guide to building The
Beginners guide to building The MPCNC machine Part03
Hello friends Welcome to the third video of building the MPCNC.
In the previous video, I built the machine's frame.
In this video I will continue with the built ,where I will start assembling the Z-axis block then I will assemble the middle section.
00:37 Review the Z axis block pieces.
01:50 Preparing the tool mount and the nut trap pieces.
05:25 Assembling the tool mount piece with the Z rails.
09:58 Assembling the Z-lower bracket with the Z rails.
11:24 Preparing the stepper motor and the Z Motor bracket and assembling them with the block.
15:13 Aligning and checking the rails nd doing the final assembling.
20:13 Adding The T8 lead screw.
22:27 Assembling the middle section stage 01 : Preparing the XYZ pieces.
26:18 Assembling the middle section stage 02 : Preparing the XY pieces and Tension Bolts A.
33:52 Assembling the middle section stage 03 : Join the XYZ with the XY pieces with Tension Bolt B.
40:56 Assembling the middle section stage 04 : Adding the brass T8 nut and Tension Bolt C.
46:45 Assembling the middle section stage 05A: Putting the X and Y middle tubes into the middle section and doing some movment controling.
54:09 Assembling the middle section stage 05B : Combining the Z axis block with the middle section.
56:39 Cheking the perpendicularity of the X and Y tubes and doing some controling.
Link to Beginners guide to building The MPCNC machine Part 01
01-Beginners guide to building The MP...
Link to Beginners guide to building The MPCNC machine Part 02
02-Beginners guide to building The MP...
The official website:
https://www.v1engineering.com/
Mostly Printed CNC "MPCNC" BURLY F-25mm OD page on Thingiverse website For Downloading the Set:
https://www.thingiverse.com/thing:790533
Z axis Drilling figure:
https://www.v1engineering.com/wp-cont...
MPCNC M4 nut case:
https://www.thingiverse.com/thing:303...
The Music: Atmospheria By Francis Preve
Hello friends Welcome to the third video of building the MPCNC.
In the previous video, I built the machine's frame.
In this video I will continue with the built ,where I will start assembling the Z-axis block then I will assemble the middle section.
00:37 Review the Z axis block pieces.
01:50 Preparing the tool mount and the nut trap pieces.
05:25 Assembling the tool mount piece with the Z rails.
09:58 Assembling the Z-lower bracket with the Z rails.
11:24 Preparing the stepper motor and the Z Motor bracket and assembling them with the block.
15:13 Aligning and checking the rails nd doing the final assembling.
20:13 Adding The T8 lead screw.
22:27 Assembling the middle section stage 01 : Preparing the XYZ pieces.
26:18 Assembling the middle section stage 02 : Preparing the XY pieces and Tension Bolts A.
33:52 Assembling the middle section stage 03 : Join the XYZ with the XY pieces with Tension Bolt B.
40:56 Assembling the middle section stage 04 : Adding the brass T8 nut and Tension Bolt C.
46:45 Assembling the middle section stage 05A: Putting the X and Y middle tubes into the middle section and doing some movment controling.
54:09 Assembling the middle section stage 05B : Combining the Z axis block with the middle section.
56:39 Cheking the perpendicularity of the X and Y tubes and doing some controling.
Link to Beginners guide to building The MPCNC machine Part 01
01-Beginners guide to building The MP...
Link to Beginners guide to building The MPCNC machine Part 02
02-Beginners guide to building The MP...
The official website:
https://www.v1engineering.com/
Mostly Printed CNC "MPCNC" BURLY F-25mm OD page on Thingiverse website For Downloading the Set:
https://www.thingiverse.com/thing:790533
Z axis Drilling figure:
https://www.v1engineering.com/wp-cont...
MPCNC M4 nut case:
https://www.thingiverse.com/thing:303...
The Music: Atmospheria By Francis Preve
4 سال پیش
در تاریخ 1399/01/18 منتشر شده
است.
1,560
بـار بازدید شده